- Not all the frames are legible, but if we start with the greyscale scans most can be read with some photoshop manipulation. Photoshop photomerge works well on most of the drawings if they are rotated to within .1 degree, and cropped before merge.
- There are duplicates of some of the drawings so you need to search for the most legible and closest to current Pampanito drawing. Note well that Pampanito underwent refit after each war patrol, including a very significant set of upgrades in summer 1945. These changes are often not reflected in many of these drawings.
- We also have the Guppy II microfilm from SS-381 scanned, the last reel has an index that has not been OCR'd or re-keyed. Much of the equipment remains the same, but there where upgrades to almost all the systems.
- The Pampanito collection has some paper drawings deaccessioned from NARA that may be better than the microfilm in some cases. These have not been scanned.
- In addition to the microfilm, we have scans of the following drawings retained by National Archives.
225# air systems diagram.tif
600# & 10# m.b. tank blow system.tif
3000# air system diagram.tif
arrangement of equip in control room_2.tif
arrangement of equip in control room.tif
arrangement of jt sonar equip.tif
ballast trim & drain diagram.tif
compartment and access.tif
conning tower rear elev plan.tif
escape arrangements.tif
firecontrol.jpg
flood & vent valves general arrangement.tif
foundation mag compass.tif
fresh water and plumbing systems diagram.tif
fuel oil system diagram.tif
hydraulic system diagram.tif
lead ballast stowage.tif
moment diagram.tif
officers quarters-rearrangement of stbd staterooms.tif
oxygen system diagram.tif
radar foundation.tif
salvage system general arrangement.tif
ss383dockingplan.tif
target des system for submarine.tif
ventilation systems diagram.tif
washing machine.tif
- This index was created in a fast process, no attempt record the buships drawing numbers, revision number, last revision date, or image quality. If there is a lot of usage of this index it might make sense to start adding this detail and accurate title block descriptions.
reel-frame |
description |
reel 1 |
01-001-003 |
battery woodwork |
01-004-005 |
dc mag controller for dc/ac mg set |
01-006-007 |
lighting system outboard lights wiring diagram |
01-008-009 |
lighting system wiring deck plan |
01-010-012 |
lighting system list of feeders, wiring appliances & fixtures block and elementary wiring diagram |
01-013-014 |
lighting system switchboard assembly and wiring diagram |
01-015-017 |
lube oil & circulating water alarm system elementary & isometric wiring diagrams circuit 1ec |
01-018-021 |
hull opening indicator sys elem.&isometric wiring diagrams circuit tr |
01-022-23 |
ic system circuit tr 44 dial indicator for hull opening assembly |
01-024-25 |
ic system circuit tr 44 dial indicator for hull opening details |
01-026-027 |
ic system circuit tr 44 dial indicator for main ballast tank valves assembly |
01-028-029 |
ic system circuit tp 32 dial indicator for main ballast tank valves details-sh1 |
01-030-031 |
ic system circuit tp 32 dial indicator for main ballast tank valves details-sh2 |
01-032-033 |
ic system circuit tp 32 dial indicator for main ballast tank valves details-sh3 |
01-034-035 |
ic system circuit tr 14 & 12 32 dial indicator for hull openings assembly & details |
01-036-037 |
summary of ac & dc loads on ac & ic switchboards |
01-038-039 |
interior communications system wiring deck plan-forward |
01-040-041 |
interior communications system wiring deck plan-aft |
01-042-043 |
illegible |
01-044 |
hydrogen detector circuit hyd elementary and isometric wiring diagrams |
01-045-046 |
interior communication battle telephone call bell system elementary & isometric wiring diagram circuit e |
01-047-048 |
mounting panels for pyrometer lube oil circ. water alarm and telephone equip in engine rooms |
01-049-50 |
marker buoy system elem. & isometric wiring diagram circuit bt |
01-051 |
engine control indicator sys elementary & isometric wiring diagram circuit 3mb |
01-052-053 |
ic system underwater log system elem. & iso. wiring diagram circuit y |
01-054-055 |
ic system shaft revolution indicator sys. elem. & iso wiring diagram circuit k |
01-056-057 |
bow diving gear auxiliary tilting indicator transmitter (6volt battery supply) |
01-058-059 |
ic system motor order telegraph elementary wiring diagram circuits 1mb&2mb |
01-060-061 |
main ballast indicator system elem & isometric wiring diags circuit tp |
01-062-063 |
hull opening indicator system contact maker operating mechanism for escape & gun access trunk doors arrangement & details |
01-064-065 |
bow diving gear plan angle transmitter operating gear details |
01-066-068 |
shaft revolution transmitter arrangement |
01-069-070 |
aux. gyro compass system elementary & isometric wiring diagram circuit xlc |
01-071 |
piping for underwater log bendix type |
01-072-076 |
interior communications switchboard assembly and details |
01-077-078 |
interior communications switchboard diagram of connections |
01-079-080 |
interior communications switchboard frame details |
01-081-082 |
interior communications switchboard resistor mounting & terminal block details |
01-083-084 |
antenna hoist motor control elementary wiring diagram |
01-085-086 |
radio transmitting & receiving circuits r-rt, r-rr & 2r-er diagrammatic & external wiring diagrams |
01-087-089 |
radio room radio apparatus-arrangement |
01-090-091 |
radio room benches, lockers & foundations details |
01-092-093 |
radio broadcast reception system arrangement in ship cir. r-rb diagrammatic and external wiring diagrams |
01-094-095 |
vertical antenna mast base plug assembly and details |
01-096-097 |
model wca-2 power training and model tbl-7 radio equipment arrangement in pump room |
01-098 |
underwater sound model jp-1 sound receiving system diagrammatic & external wiring diagrams cir s-sr |
01-099-100 |
model wca-2 echo ranging and listening equipment and model sj-1 radar equipment arrangement in the conning tower |
01-101-102 |
bathythermograph installation arrangement and details |
01-103 |
echo ranging and detection alterations to hand pump |
01-104-106 |
signal ejector arrangement |
01-107-108 |
signal ejector barrel details |
01-109-110 |
signal ejector muzzle door operating details |
01-111-112 |
signal ejector winch details |
01-113-114 |
battle telephone system elementary & isometric wiring diagrams circuits ja and xja |
01-115-117 |
forward torpedo room arrangement |
01-118-119 |
torpedo & mine handling & stowage forward & aft - mine loading pole stowage bar and nose piece details |
01-120-121 |
gauge and thermometer list |
01-122-123 |
main power system instrument panels for main generator engines assembly & details |
01-124-125 |
resistance thermometer systems isometric wiring diagram and nameplate markings |
01-126-127 |
pyrometer system elementary & isometric wiring diagrams circuit pb |
01-128-129 |
distant reading gauges hydro-static type arrangement sanitary tanks |
01-130 |
aux engine gauge boards valve & piping arrangement after engine room |
01-131-132 |
lube oil system mm & red gear gauge board valve and piping arrangement maneuvering room |
01-133-134 |
instrument panel for aux generator engine after engine room assembly & details |
01-135-136 |
shore connection switch for lighting switchboard |
01-137-138 |
mk 18 torpedo heating & hydrogen burning quick action connection box assembly & details |
01-139-140 |
circ water system horizontal swing check valve 4 1/2" nom forward engine room |
01-140-141 |
general arrangement 750 gpd vapor compressor distilling unit type xb compressor motor mounted on unit |
01-142 |
master plan standard spare parts for 750 gpd vapor compression distilling unit with type xb compressor |
01-143-145 |
arrangement 750 gpd vapor compression distilling unit |
01-146-147 |
details sheet no 1 750 gpd vapor compression distilling unit |
01-148 |
details sheet no 2 750 gpd vapor compression distilling unit |
01-149-150 |
accessories sheet no 1 750 gpd vapor compression distilling unit |
01-151-152 |
accessories sheet no 2 750 gpd vapor compression distilling unit |
01-153-154 |
accessories sheet no 3 750 gpd vapor compression distilling unit |
01-155 |
details pulley guard 750 gpd vapor compression distilling unit |
01-156 |
piping diagram 750 gpd vapor compression distilling unit (two) submarine |
01-157 |
3 gallon desuperheater tank for vapor compression distilling unit |
01-158 |
arrangement bulkhead supports vapor compression distilling unit submarines with xb compression equipped for sound isolation |
01-159 |
outline of 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-160 |
headplate gear end of 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-161 |
sectional drawings of 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-162 |
headplate drive end 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-163 |
drive end cover gear housing impeller & misc. small parts 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-164 |
cylinder shafts gears & misc. small parts 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-165 |
bolts & misc. small parts 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-166 |
motor base and gaskets 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-167 |
spare parts and special tools 5 x 6 x 8 vapor compressor for vapor compression distilling unit |
01-168-169 |
arrangement of compressor piping 750 gpd vapor compression distilling unit |
01-169 |
arrangement of compressor piping 750 gpd vapor compression distilling unit |
01-170-171 |
1 inch type 206 pressure reducing valve for sea water feed to vapor compression distilling unit |
01-172-173 |
vari pitch drive for 750 gpd vapor compression distilling unit |
01-174 |
wiring diagram controller and heaters 750 gpd vapor compression distilling unit |
reel 2 |
02-001 |
pipe berths |
02-002-003 |
ventilation system 15 1/2 and 22" hull valves detent spring assembly and details |
02-004-005 |
md-573 vacuum priming pump for use with trim pump details |
02-006-007 |
md-573 vacuum priming pump for use with trim pump details |
02-008-009 |
md-573 vacuum priming pump for use with trim pump details |
02-010-011 |
d.c. magnetic controller for priming pump |
02-012 |
outline-front and end for horizontal drive drain pump |
02-013 |
outline back and top for horizontal drive drain pump |
02-014 |
sectional assembly for horizontal drive drain pump |
02-015 |
sectional assembly for horizontal drive drain pump |
02-016 |
master list of material for horizontal drive drain pump |
02-017 |
master list of material, list of spare parts for horizontal drive drain pump |
02-018 |
frame for horizontal drive drain pump |
02-019 |
frame for horizontal drive drain pump |
02-020 |
worm, bearings, gear, crankshaft and misc. for horizontal drive drain pump |
02-021 |
bearing assemblies oil retainers & bearing cap for horizontal drive drain pump |
02-022 |
gear cover, crank cover cylinder head, plunger and misc. for horizontal drive drain pump |
02-023 |
conn rod, oil sleeve, valve detail and misc. for horizontal drive drain pump |
02-023 |
cooling coil, lubrication oil line piping misc for horizontal drive drain pump |
02-025 |
air chambers and accessories for horizontal drive drain pump |
02-026 |
relief valve details for horizontal drive drain pump |
02-027 |
flexible coupling for horizontal drive drain pump |
02-028 |
shock absorber details gauges, valves, pipes and misc. for horizontal drive drain pump |
02-029 |
gaskets and misc. for horizontal drive drain pump |
02-030 |
sectional assembly, outline and specs, d-225 dp semi-encl. self-vent motor for primer for centrifugal trimming pump |
02-031-032 |
assembly drawing trim pump |
02-033 |
pump outline, trim pump |
02-034 |
rotor details, trim pump |
02-035 |
rotor details & end cover, trim pump |
02-036-037 |
upper pump outline and details, trim pump |
02-038 |
lower pump casing and details, trim pump |
02-039 |
valve body & details, trim pump |
02-040 |
valve details, trim pump |
02-041 |
motor support, tools, spares, trim pump |
02-042 |
tools trim pump |
02-043 |
misc. hangers for piping and wiring |
02-044 |
submarine swing check valve 2 1/2 nom. size |
02-045 |
swing check valve 1 nom. size |
02-046 |
swing check valve 4' nom. size |
02-047-048 |
three way cock (5" nom" lp flanged assembly & details |
02-049-050 |
sectional assembly motor for evaporator vapor compression still |
02-051-052 |
sect. assembly outline, spares & tools, sea water pump for vapor compression distilling units. |
02-053 |
details of sea water pump for vapor compression distilling unit |
02-054-055 |
sectional assembly, outline and diagram for motor for vapor compression distilling unit |
02-055 |
echo ranging and detection equipment wt sound bearing transmitter |
02-056 |
torpedo charging panels and fittings |
02-057 |
swing check valve 1 1/2 nom size |
02-058 |
sea valve 1 inch nom size |
02-059 |
bunk covers zipper style |
02-060 |
hose and hawser reels |
02-061 |
40" cleat and roller chock |
02-062-063 |
manifold forward torpedo room torpedo tube blow and vent assembly details |
02-064 |
manifold fwd and aft torpedo room torpedo tube blow and vent details |
02-065 |
manifold aft torpedo room torpedo tube blow and vent assembly & details |
02-066 |
trim manifold 3" - 2 valve ford & aft torpedo rooms |
02-067-068 |
impulse air manifold 1/2" ips torpedo rooms |
02-069 |
trim systems drain pump suction 3" special globe valve |
02-070 |
water & drainage system bilge suction manifold 2" - 2 valve |
02-071 |
1" manifold divers connections escape trunk |
02-072 |
forward tank blow and vent manifold |
02-073-074 |
bow buoyancy vent valve, valve, valve cover & gratings |
02-075-076 |
bow diving gear sector gears and connecting rod details |
02-077 |
bow diving gear, bearings for plane stocks |
02-078 |
bow diving gear, bevel gears-shafts and bearing casting for rigging |
02-079 |
bow diving gear details |
02-080-081 |
wt door conning tower and escape trunk, inboard closing device, gear case details |
02-082 |
hydraulic system accumulator capacity 1000 cu in details sheet no 1 |
02-083 |
flood valves hydraulic operated bracket details safety tank |
02-084 |
flood valves hydraulic operating gear cylinder & cover details safety tank |
02-085 |
flood valves hydraulic operating gear piston and hand crank details safety tank |
02-086-87 |
steering gear hydraulic system, bow and stern diving gears, windlass & capstan & bow tilting vent & surge tanks arrangement and details |
02-088 |
mast for vertical antenna, hull bearing details |
02-089 |
no 1 and 2 periscopes azimuth circle arrangement and details |
02-090-091 |
stern post casting details |
02-092-093 |
steering gear, rudder and rudder stock |
02-094-095 |
steering gear, rudder stock crosshead and details |
02-096 |
stern diving gear, tiller connecting rod and cross head details |
02-097 |
bow and stern diving gear, control cylinders & foundation details |
02-098 |
bow and stern diving gear, control cylinders lever & shaft details |
02-099 |
bow and stern diving gear, hydraulic relief valve manifold assembly |
02-100 |
bow and stern diving gear, hydraulic relief valve manifold details |
02-101 |
bow and stern diving gear, hydraulic control valve details of body |
02-102 |
bow and stern diving gear, hydraulic control valve details |
02-103 |
special 2" nom size macomb strainer lube oil system motor room& engine room |
02-104 |
steering gear connecting rod & guide details sheet 3 |
02-105 |
steering gear cylinder & plunger details sheet 1 |
02-106 |
torpedo handling and stowage nose piece & loading pole details |
02-107 |
torpedo handling and stowage nose piece details |
02-108 |
safety tank vent valve arrangement |
02-109-110 |
safety tank vent valve valve body details |
02-111-112 |
safety tank vent valve valve cover & link details |
02-113-114 |
lines for stern post and rudder |
02-115 |
main ballast vent valve main ballast no 1 valve body details |
02-116 |
main ballast vent valve special tee details main ballast no 7 |
02-117-118 |
stern diving gear ram type cylinder & sleeve & mech. indicator details |
02-119 |
flood valves negative tank seat & cover details |
02-120 |
flood valves negative tank-hydraulic operating gear hand crank details |
02-121 |
flood valves negative tank connecting rod & bearing details |
02-122 |
hydraulic operating gear extension shaft details safety tank |
02-123 |
stern capstan worm gear arrangement & details |
02-124 |
stern capstan worm gear case details |
02-125 |
stern capstan head, shaft & shaft bearing details |
02-126 |
steering gear - bow and stern diving gear hydraulic system & capstan 1/8 hydraulic valve |
02-127 |
bow buoyancy vent valve operating line and shaft details |
02-128 |
torpedo and mine handling and stowage aft loading chocks details sheet 1 |
02-129-130 |
trim pump-100 gallons vertical, duplex single acting vertical and horizontal drive discharge indicator |
02-131 |
contact maker type b |
02-132 |
pushbutton portable gang switch watertight periscope motors |
02-133 |
sliding doors for lower berths in officers and cpo quarters |
02-134 |
slack wire switch for radio mast and periscope hoist |
02-135-136 |
limit switch quick break single pole class a drip proof 1 amp 250 vdc, 10 amp 250 vac shockproof class 150 assembly and details |
02-137 |
3 inch standard swing check valve 3 1/2 bore |
02-138-139 |
motor starter drum type manually operated for 15-40 hp 125 volt, 30-80 hp 250 volt motor assembly and wiring details |
02-140 |
motor starter drum type manually operated details sheet no 1 |
02-141 |
motor starter drum type manually operated details sheet no 2 |
02-142 |
motor starter drum type manually operated details sheet no 3 |
02-143 |
motor starter drum type manually operated details sheet no 4 |
02-144 |
motor starter drum type manually operated details sheet no 5 |
02-145 |
motor starter drum type manually operated details sheet no 6 |
02-146 |
motor starter drum type manually operated details sheet no 7 |
02-147 |
motor starter drum type manually operated details sheet no 8? |
02-148 |
motor starter drum type manually operated details sheet no 9 |
02-149-150 |
motor starter drum type manually operated details sheet no 10 |
02-151-152 |
motor starter drum type manually operated for 5-10 hp 125 volt, 10-30 hp 250 volt motor assembly and wiring details |
02-153 |
motor starter drum type manually operated details sheet no 1 |
02-154 |
motor starter drum type manually operated details sheet no 2 |
02-155 |
motor starter drum type manually operated details sheet no 3 |
02-156 |
motor starter drum type manually operated details sheet no 4 |
02-157 |
motor starter drum type manually operated details sheet no 5 |
02-158 |
motor starter drum type manually operated details sheet no 6 |
02-159 |
motor starter drum type manually operated details sheet no 7 |
02-160 |
motor starter drum type manually operated details sheet no 8? |
02-161-162 |
flood valves hand operated gear bracket details |
02-163 |
torpedo and mine stowage handling and stowage forward and aft special block for breech ring |
02-164-165 |
crews mess galley scullery and storeroom arrangement |
02-166-167 |
battery cell handling gear forward and aft |
02-168 |
echo sounding projector shell housing |
02-169-170 |
crews mess benches |
02-171 |
stem casting and towing fairlead |
02-172 |
battery fresh water tanks |
02-173-174 |
torpedo handling and stowage after deck skid |
02-175-176 |
berthing in after torpedo room |
02-177 |
main storage battery tanks rubber lining |
02-178-179 |
foundations for reduction gears and main motors |
02-180-181 |
officers & cpo quarters arrangement |
02-182 |
miscellaneous joiner details wood - barometer and thermometer stowage |
02-183-184 |
foundations for gyro setting indicator regulators |
02-185 |
stern chock & foundation |
02-186-187 |
berthing in forward torpedo room |
02-188 |
sidelight boxes |
02-189 |
loading sequence for installing storage battery cells forward and aft battery compartment |
02-190 |
conning tower fairwater & bridge joiner work seats and platforms |
02-192-193 |
bow framing sections |
02-194 |
warming oven porcelain enameled |
02-195 |
supports for nos 1 and 2 periscopes and vertical antenna mast and radar |
reel 3 |
03-001 |
fuel oil, water and drainage piping officers quarters |
03-002-003 |
fuel oil, water and drainage piping control room |
03-004 |
ventilation system battery ventilation details |
03-005 |
sea valve 5" size |
03-006-008 |
fuel oil, water and drainage piping arrangement in after torpedo room |
03-009 |
gauge list for c&r piping system |
03-010-011 |
displacement and other curves |
03-012-13 |
bonjean curves |
03-014-015 |
bow diving gear plane details |
03-016 |
location table for clinometer & trim indication tubes |
03-017-018 |
torpedo & mine handling and stowage forward roller brackets arrangement |
03-019 |
flood valves hand operating gear extension shaft arrangement |
03-020 |
flood valves crankshaft details |
03-021 |
flood valves cover toggle link details |
03-022 |
flood valves bell crank foundations and stops |
03-023 |
flood valves bell crank details |
03-024 |
flood valves connecting rod and bearing details |
03-025 |
flood valves hand operating gear extension shaft & bearing details |
03-026 |
torpedo and mine handling and stowage-forward and aft roller brackets details sheet 1 |
03-027-028 |
torpedo and mine handling and stowage aft roller brackets and arrangements |
03-029-030 |
torpedo and mine handling and stowage forward and aft roller brackets details sheet 3 |
03-031 |
torpedo and mine handling and stowage forward and aft roller brackets details sheet 2 |
03-032-033 |
torpedo and mine handling and stowage forward and aft roller brackets details sheet 4 |
03-034-035 |
torpedo and mine handling and stowage forward roller brackets details sheet 5 |
03-036-037 |
torpedo and mine handling and stowage forward and aft cradle lock details |
03-038-039 |
flood valves hand operating gear hand crank details |
03-040 |
flood valves hand operating gear operating screw details |
03-041-042 |
model sj radar equipment training mechanism speed reducers (outline dim.) |
03-043-044 |
emergency vent valve valve cover shafts and misc. details, mb 4a and 4b |
03-045 |
emergency vent valve wrench stuffing box & misc. details md 4a and 4b |
03-046 |
main ballast vent valve 4a & 4b arrangement |
03-047-048 |
main ballast vent valve body details 4a & 4b |
03-049-050 |
main ballast vent valve 4a & 4b valve cover and link details |
03-051-052 |
hydraulic system main manifold detail sheet 1 |
03-053 |
hydraulic system main manifold detail sheet 2 |
03-054-055 |
hydraulic system main manifold detail sheet 3 |
03-056-057 |
hydraulic system oil supply tank strainer and air tank and details |
03-058-059 |
torpedo & mine handling & stowage aft roller brackets details sheet no 1 |
03-060-061 |
torpedo & mine handling & stowage aft roller brackets details sheet no 2 |
03-062-063 |
torpedo & mine handling & stowage forward work table arrangement & details |
03-064 |
torpedo & mine handling & stowage forward cradle lifting eye & lock details details |
03-065-066 |
torpedo & mine handling & stowage loading chocks arrangement |
03-067-068 |
torpedo & mine handling & stowage aft roller brackets details sheet no 3 |
03-069-070 |
torpedo & mine handling & stowage forward and aft loading chocks details sheet no 1 |
03-071 |
torpedo & mine handling & stowage aft roller brackets details sheet no 4 |
03-072-073 |
stern diving gear plane details |
03-074-075 |
stern capstan control switch operating mechanism arrangement |
03-076 |
stern capstan control switch operating mechanism details |
03-077-078 |
hydraulic system automatic bypass and non-return valve arrangement |
03-079-080 |
hydraulic system automatic bypass and non-return valve detail sheet 1 |
03-081-082 |
hydraulic system automatic bypass and non-return valve detail sheet 2 |
03-083-084 |
torpedo and mine handling and stowage forward arrangement |
03-085-086 |
torpedo and mine handling and stowage forward upper tracks at frame 24 details |
03-087-088 |
torpedo and mine handling and stowage forward removable track sections details |
03-089-090 |
torpedo and mine handling and stowage forward middle tracks at frame 24 details |
03-091-092 |
torpedo and mine handling and stowage forward tracks at frame 24 arrangement |
03-093-094 |
steering gear drive shaft details sheet 2 |
03-095 |
steering gear drive shaft details sheet 1 |
03-096-097 |
steering gear control cylinder details sheet 2 |
03-098-099 |
torpedo and mine handling and stowage forward upper tracks arrangement |
03-100-101 |
torpedo and mine handling and stowage forward and aft cradle weldment after machining |
03-102 |
torpedo and mine handling and stowage aft upper tracks arrangement |
03-103-104 |
torpedo and mine handling and stowage forward and aft cradle weldment before machining |
03-105 |
torpedo and mine handling and stowage forward track details brackets and clips |
03-106-107 |
torpedo and mine handling and stowage forward middle tracks arrangement |
03-108 |
torpedo and mine handling and stowage aft tracks at frame 110 arrangement |
03-109-110 |
torpedo and mine handling and stowage aft upper tracks details |
03-111-112 |
torpedo and mine handling and stowage aft cradle lower tracks and removable sections |
03-113 |
torpedo and mine handling and stowage aft tracks at frame 117 arrangement |
03-114-115 |
torpedo and mine handling and stowage forward and aft cradle lifting gear and chain hoists |
03-116-117 |
torpedo and mine handling and stowage forward and aft nose lines and capstan line |
03-118-119 |
hydraulic system oil supply tank and details |
03-120-121 |
torpedo and mine handling and stowage aft arrangement |
03-122-123 |
steering gear cylinder and plunger detail sheet 1 |
03-124-125 |
steering gear cylinder foundation details |
03-126-127 |
steering gear drive shaft details sheet 3 |
03-128-129 |
wt door conning tower & escape trunk inboard closing device lever and indicator details |
03-130-131 |
foundations in forward torpedo room cable cutting control panel and wca motor generator panel |
03-132 |
stern diving gear bearing and coupling details |
03-133-134 |
35 gallon drain - 100 gallon trim vertical duplex single acting vert and horizontal drive couplings |
03-135 |
shock absorbers for hydraulic, air, water systems with silbraz unions |
03-136-137 |
torpedo and mine stowage. lashing strap saddle for mark xii mine |
03-138 |
sanitary tank vents deodorant container |
03-139-140 |
fresh water tanks test manifold |
03-141 |
extension stems (reach rods for valves) |
03-142-143 |
torpedo and mine handling and stowage lashing straps arrangement, mark iv torpedo, mark x mine, mark xii mine |
03-144 |
silbraz 1"x1" hydraulic strainer |
03-145-146 |
torpedo and mine handling and stowage forward and aft torpedo servicing cradle assembly & details |
03-147-148 |
hydraulic system pilot valve for automatic bypass valve arrangement details |
03-149-150 |
hydraulic system pilot valve for automatic bypass valve details |
03-151-152 |
steering gear & hydraulic system cut-out valve (plug valve) details |
03-153-154 |
steering gear & hydraulic system cut-out valve (plug valve) details & arrangement |
03-155-156 |
hydraulic system oil supply tank cut-out valve arrangement |
03-157-158 |
hydraulic system oil supply tank cut out valve details |
03-159 |
foundation in forward torpedo room for echo ranging listening equipment |
03-160-161 |
foundations topside for windlass wildcat frame and capstan gear case |
03-162 |
foundations in control room |
03-163 |
protectors-zinc |
03-164 |
upper limit switch-quick break double pole for antenna and periscope hoists assembly and details |
03-165-166 |
alarm bell for refrigeration space mechanical |
03-167 |
battery ventilation controller wiring diagram revision for installation requirement |
03-168 |
modification of upper limit switch for antenna mast hoist |
03-169-170 |
bow and stern diving gear, stern capstan control and bow plane rig and winding system elemental wiring diagram |
03-171-172 |
pump room arrangement |
03-173-175 |
keel |
03-176-177 |
frames 17-18-19-20-21 |
03-178-179 |
frames 22-23-24-25-26 |
03-180-181 |
frames 27-28-29-30 |
03-182-183 |
frames 31-32-33-34 |
03-184-185 |
frames 108-109-110-111 |
03-186 |
frames 112-113-114-115 |
03-187 |
frames 116-117-118-119 |
03-188-189 |
frames 120-121-122-123-124 |
03-190-191 |
ships air flasks-stowage in main ballast tanks |
03-192-193 |
bulkhead 35 |
03-194-195 |
bulkhead 35 |
03-196 |
bulkhead 9" aft frame 47 |
03-197-198 |
bulkhead 13 1/2" forward frame 99 |
03-200 |
bulkhead 107 |
03-201-202 |
torpedo loading hatches |
03-203-204 |
forward escape trunk structure |
03-205-206 |
forward torpedo room tank top |
03-207 |
after torpedo room tank top |
03-208-209 |
bow framing elevation & flats |
03-210-211 |
bow framing sections 10 to 16 incl. |
03-212-214 |
stern details, illegible title block |
03-215 |
shaft tubes and bossing |
03-216-217 |
conning tower structural details |
03-218-219 |
access and escape hatch (with rescue chamber seating and skirt) after torpedo room frames 115-116 |
03-220-222 |
platform deck crews quarters galley and crews mess |
03-223-224 |
bulkheads non-structural crews w.c. washroom and showers |
03-225-226 |
windlass and capstan general arrangement |
03-227-228 |
windlass and capstan hawse pipe outboard section |
03-229-230 |
windlass and capstan hawse pipe inboard section |
03-231 |
windlass and capstan wildcat clutch bracket details |
03-232-233 |
windlass and capstan wildcat frame details |
03-234-235 |
windlass and capstan wildcat and spur gear details |
03-236 |
windlass and capstan chain compressor arrangement and details |
03-237 |
windlass and capstan chain compressor frame details |
03-238 |
windlass and capstan band brake gear case details |
03-239 |
windlass and capstan band brake gear and gear details |
03-240-241 |
windlass and capstan wildcat clutch details |
03-242-243 |
windlass and capstan shaft and gear details |
03-244 |
windlass and capstan chain compressor deck indicator details |
03-245 |
windlass and capstan anchor chain deck indicator details |
03-246 |
windlass and capstan chain slip arrangement |
03-247 |
windlass and capstan chain slip details |
03-248-249 |
windlass and capstan main drive bevel gear details |
03-250-251 |
flood valves arrangement at frames 58 and 60 port and starboard |
03-252-253 |
flood valves arrangement at frames 70, 72 and 74 port and starboard |
03-254 |
flood valves arrangement at frames 76 and 79 port and starboard |
03-255 |
flood valves valve cover details |
03-256-257 |
flood valves seat and cover details safety tank |
03-258-259 |
flood valves frame and seat details |
03-260-261 |
flood and vent valves general arrangement |
03-262-263 |
torpedo tube drain manifold two valve assembly and details after torpedo room |
03-264-265 |
torpedo tube drain manifold two valve details after torpedo room |
03-266-267 |
steering gear pump manifold arrangement |
03-268-269 |
steering gear pump manifold body casting |
03-270 |
steering gear pump manifold valve details |
03-271 |
2 1/2" special angle valve main ballast tank low pressure blow |
03-272-273 |
5" overflow valve after wrt tank arrangement and details |
03-274-275 |
5" overflow valve after wrt tank operating gear arrangement and details |
03-276-277 |
stern diving gear (ram type) tilting rod piston and miscellaneous details |
03-278-279 |
steering gear pump control details |
03-280-281 |
shaft struts |
03-282-283 |
torpedo tube drain manifold three valve assembly and details forward torpedo room |
03-284-285 |
torpedo tube drain manifold three valve details forward torpedo room |
03-286 |
torpedo tubes drain valve operating gear arrangement and details forward torpedo room |
03-287-288 |
torpedo tube drain manifold operating gear forward torpedo room |
03-289 |
bow buoyancy vent valve miscellaneous foundations |
03-290 |
bow buoyancy vent valve shaft fork and link details |
03-291 |
bow buoyancy vent valve shaft fork and link details |
03-292-294 |
bow buoyancy vent valve arrangement |
03-295-296 |
bow buoyancy vent valve bearing rocker arm and bell crank details |
03-297-298 |
torpedo and mine handling stowage forward and aft cradle arrangement |
03-299-300 |
torpedo and mine handling stowage forward and aft cradle details |
03-301 |
torpedo and mine handling stowage forward and aft cradle details chocks cleat |
03-302-303 |
torpedo and mine handling stowage aft loading chocks arrangement |
03-304-305 |
shaft tube castings |
03-306-307 |
steering gear change valve arrangement |
03-308-309 |
steering gear change valve body |
03-310-311 |
steering gear change valve details |
03-312-313 |
low pressure blow system list control manifold assembly and details |
03-314-315 |
stern diving gear (ram type) tilting gear arrangement |
03-316-317 |
water and drainage forward and aft torpedo rooms special fittings |
reel 4 |
04-001-002 |
torpedo and mine handling and stowage forward middle tracks at frame 31 details |
04-003-004 |
torpedo and mine handling and stowage forward upper tracks at frame 31 details |
04-005-006 |
torpedo and mine handling and stowage forward middle and lower tracks at frame 31 detail |
04-007-008 |
torpedo and mine handling and stowage forward tracks at frame 31 arrangement |
04-009-010 |
stern diving gear stuffing box and gland for tilting rod tube |
04-011-012 |
stern diving gear mechanical indicator details |
04-013 |
hardie-tynes - general arrangement circulating water system 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-014 |
hardie-tynes - water piping details and tube fittings 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-015 |
hardie-tynes crank shaft and crank pin brasses 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-016 |
l.h. differential cylinder block 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-017 |
third and fourth cylinders & heads 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-018 |
r.h. differential cylinder block 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-019 |
air cylinder f.f. lubrication drive differential cylinder block 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-020 |
third cylinder shell 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-021 |
fourth cylinder shell 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-022 |
connecting rod ball end boxes and yoke 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-023 |
main bearing caps and boxes 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-024 |
oil pressure piping to bearings 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-025 |
pistons and liners 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-026 |
compressor base plate 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-027 |
details of bureau of ships no. 2 oil compressor pump 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-028 |
air and water relief valves 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-029 |
after cooler 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-030 |
general assembly of lubricator 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-031 |
air pipe guards 6 1/2"-5 7/16" - 2 1/2" - 1 1/4" x 4 1/2" high pressure air compressor |
04-032 |
standard universal joints |
04-033 |
valve compartment air supply 225# service |
04-034-035 |
salvage air system compartment salvage valve and outboard connection |
04-036 |
bulkhead grease valve and wrenches |
04-037 |
folding lavatory |
04-038 |
hardie-tynes machining diagram for connecting flange and pad for motor - high pressure air compressor |
04-039-040 |
watertight door stop, latch and buffer arrangement and details |
04-041 |
fuel oil tanks blow, vent and test manifold |
04-042 |
air expulsion water closet metal bowl |
04-043-044 |
hatch covers 21"x27" oval general arrangement |
04-045-046 |
hatch covers 21"x27" oval cover details |
04-047-048 |
hatch covers 21"x27" oval miscellaneous details |
04-049-050 |
hatch covers 21"x27" oval latch details |
04-051-052 |
bow and stern diving gear tilting block centering device for hydraulic pumps |
04-053-054 |
fresh water and plumbing piping in forward torpedo room |
04-055-056 |
fresh water and plumbing piping arrangement in after torpedo room |
04-057-058 |
gauge boards control room |
04-059-060 |
water and drainage system piping arrangement motor and maneuvering rooms |
04-061-062 |
hydrogen detector arrangement of piping for battery exhaust |
04-063-064 |
manifold 3" fuel oil system |
04-065-066 |
locking devices for standard and common valves |
04-067 |
water and drainage system 2" suction manifold |
04-068-069 |
w.c. valve box |
04-070-071 |
ventilation system crew's mess, galley and magazine arrangement |
04-072-074 |
fresh water and plumbing piping arrangement officers quarters and forward battery compartment |
04-075 |
escape trunk flood valve and operating gear arrangement and details |
04-076-077 |
low pressure blow manifold clapper valve details |
04-078-079 |
3000# air system diagram |
04-080-081 |
600# and 10# main ballast tank blow diagram |
04-082-083 |
225# air system diagram |
04-084-085 |
salvage air system diagram |
04-086-087 |
trimming and drainage diagram |
04-088-089 |
fuel oil system diagram |
04-090-091 |
hydraulic system diagram |
04-092-093 |
air system low pressure blow manifold assembly |
04-094-095 |
flood valves hydraulic operating gear arrangement safety tank |
04-096 |
flood valves hydraulic operating gear operating rod and crosshead details safety tank |
04-097 |
flood valves negative tank arrangement |
04-098-099 |
flood valve negative tank hydraulic operating cylinder and piston details |
04-100-101 |
flood valves hand operating gear arrangement hull mounted |
04-102-103 |
flood valves hand operating gear indicator details |
04-104-105 |
torpedo and mine handling and storage forward and aft wrenches gauge plug and cradle stacking plate |
04-106-107 |
bow and stern diving gear hydraulic change valve details of valve body |
04-108-109 |
steering gear conning tower and control room steer stand shaft arrangement |
04-110-111 |
steering gear control room steering stand arrangement |
04-112-113 |
steering gear control room steering stand detail sheet 1 |
04-114-115 |
steering gear control room steering stand detail sheet 2 |
04-116-117 |
steering gear control room steering stand detail sheet 3 |
04-118-119 |
standard 30" tubular handwheel details |
04-120-121 |
hydraulic system accumulator capacity 1000 cu in arrangement |
04-122-123 |
hydraulic system accumulator capacity 1000 cu in details sheet 2 |
04-124-125 |
hydraulic system accumulator capacity 1000 cu in details sheet 3 |
04-126 |
steering gear control room steer stand detail sheet 4 |
04-127 |
steering gear control room steer stand detail sheet 5 |
04-128-129 |
steering gear control room steer stand detail sheet 6 |
04-130-131 |
steer gear and hydraulic system emergency steer gear control valve arrangement |
04-132-133 |
steer gear and hydraulic system emergency steering gear control valve detail sheet 1 |
04-134-135 |
steering gear and hydraulic system emergency steering gear control valve details sheet no 2 |
04-136-137 |
steering gear and hydraulic system emergency steering gear control valve details sheet no 3 |
04-138 |
steering gear pump control operating lever arrangement |
04-139-140 |
steering gear pump control operating lever details |
04-141-142 |
hydraulic system main supply manifold arrangement |
04-143-144 |
main ballast vent valve main ballast no 7 installation |
04-145-146 |
main ballast vent valve hull castings main ballast no 1 and 7 |
04-147-148 |
main ballast tank emergency vent valve arrangement |
04-149-150 |
foundation 4" gun mk xiii |
04-151-152 |
miscellaneous tanks in forward torpedo room arrangement and details |
04-153-155 |
platform deck covering |
04-156 |
sound isolation motor generator for underwater sound forward torpedo room |
04-157-158 |
superstructure frames 17 to 19 incl. |
04-159 |
superstructure frames 20 to 23 incl. |
04-160-161 |
superstructure frames 24 to 31 incl. |
04-162-163 |
superstructure frames 32 to 43 incl. |
04-164-165 |
superstructure frames 44 to 55 incl. |
04-166-167 |
superstructure frames 110 to 124 incl. |
04-168 |
s.t. steel material for conning tower |
04-169-170 |
stowage of fuel oil filling hose |
04-171-173 |
ladders and grabs |
04-174-175 |
four inch gun firing clearances |
04-176-177 |
2 1/2" hull stop valve quick operating |
04-178-179 |
3" hull stop valve quick operating |
04-180 |
3 1/2" hull stop valve quick operating |
04-181 |
4 1/2" hull stop valve quick operating |
04-182 |
sea valve 3/4" nominal size |
04-183 |
sea valve 1 1/4" nominal size |
04-184-185 |
sea valve 2" nominal size |
04-186-187 |
sea valve 2 1/2" nominal size |
04-188 |
sea valve 3" nominal size |
04-189 |
sea valve 3 1/2" nominal size |
04-190 |
sea valve 4" nominal size |
04-191 |
sea valve 4 1/2" nominal size |
04-192 |
sea valve 5" nominal size |
04-193 |
sea valve 5 1/2" nominal size |
04-194 |
air tight dampers ventilation terminals |
04-195 |
4" nominal macomb strainer |
04-196 |
sight glass boxes (door viewing ports) |
04-197 |
sea valve 1 1/2" nominal size |
04-198 |
sea valve 6" nominal size |
04-199 |
3/4" nominal macomb strainer |
04-200 |
1" nominal macomb strainer |
04-201 |
1 1/4" nominal macomb strainer |
04-202 |
1 1/2" nominal macomb strainer |
04-203 |
bulkhead fitting special for liquidometer |
04-204-205 |
ventilation system 5" grace line terminal diffusing |
04-206-207 |
watertight door exterior circular 30" diameter general arrangement |
04-208-209 |
watertight door exterior circular 30" diameter door details |
04-210-211 |
watertight door exterior circular 30" diameter gear details |
04-212-213 |
watertight door exterior circular 30" diameter latch and miscellaneous details |
04-214-215 |
2 1/2" nominal macomb strainer |
04-216-217 |
bulkhead and hull connections |
04-218-219 |
3" nominal macomb strainer |
04-220-221 |
3 1/2" nominal macomb strainer |
04-222 |
deck drains-traps 1 1/2 and 2 inch |
04-223 |
2" deck drain valve |
04-224-225 |
2" gooseneck valve fuel oil system drainage system |
04-226-227 |
2" nominal macomb strainer |
04-228 |
5" nominal macomb strainer |
04-229 |
1 1/2" deck drain valve |
04-230 |
4 1/4" macomb strainer |
04-231-232 |
hatch cover 25" diameter dished plate general arrangement |
04-233-234 |
hatch cover 25" diameter dished plate cover spider and toggle details |
04-235-236 |
hatch cover 25" diameter dished plate miscellaneous details |
04-237-238 |
hatch cover 25" diameter dished plate standard, escape , conning tower and torpedo loading springs and miscellaneous details |
04-239-240 |
hatch cover 25" diameter dished plate for conning tower general arrangement (also for gun access) |
04-241-242 |
hatch cover 25" diameter dished plate for conning tower cover, spider and toggle details (also for gun access) |
04-243-244 |
hatch cover 25" diameter dished plate for conning tower miscellaneous details (also for gun access) |
04-245-246 |
fittings for 1/4" o.d. tubing pressure gauges- gauge boards |
04-247 |
ventilation system pitot tube asme standard assembly and details |
04-248-249 |
main ballast safety tank emergency vent valve and liner details |
04-250-251 |
watertight door forward escape trunk 30" circular door frame details |
04-252-253 |
no 1 and no 2 periscopes stuffing box and misc details |
04-254-255 |
w.t. door forward escape trunk inboard closing device shaft and universal joint details |
04-256-257 |
w.t. door forward escape trunk inboard closing device arrangement |
04-258-259 |
no 1 and 2 periscopes lower limit switch details |
04-260-261 |
no 1 and 2 periscopes bumper and misc. details |
04-262-263 |
no 1 and 2 periscopes lower limit switch arrangement |
04-264 |
bypass check valve with strainers for 1" pipe line |
04-265-266 |
steering gear conning tower steering stand arrangement |
04-267-268 |
no 1 and 2 periscopes light shield details |
04-269-270 |
no 1 and 2 periscopes azimuth circle support and extension ring details |
04-271 |
hatches frames and covers list |
04-272-273 |
access hatch flush type welded 20" x 20" and 15" x 23" |
04-274-275 |
bow and stern diving gear hydraulic change valve arrangement |
04-276-277 |
bow and stern diving gear hydraulic change valve details |
04-278-279 |
steering gear conning tower steering stand gear case and details |
04-280-281 |
1/8" hydraulic valve for .405" o.d. pipe, .250" o.d. pipe with silbraz union |
04-282-283 |
3/4" hydraulic valve with silbaz union |
04-284-285 |
mast for vertical antenna details of mast |
04-286-287 |
mast for vertical antenna arrangement |
04-288-289 |
mast for vertical antenna hull bearing and upper limit switch arrangement |
04-290-291 |
mast for vertical antenna spring buffer and lower limit switch arrangement |
04-292-293 |
mast for vertical antenna spring buffer details |
04-294 |
hatch cover 21" x 27" oval and 25" diameter d.p. foundation for latches |
04-295-296 |
hatch cover 21" x 27" oval location stop for dog handle in wide open position |
04-297-298 |
model sj radar equipment training mechanism general arrangement |
04-299-300 |
model sj radar equipment training mechanism arrangement of lower end |
04-301-302 |
model sj sj-1 radar equipment training mechanism bearing details |
04-303-304 |
model sj radar equipment training mechanism hand wheel and shaft details |
04-305-306 |
main ballast vent valves main ballast no 1 valve cover and link details |
04-307-308 |
emergency vent valve main ballast group 2-forward ballast group #3-#5 (and main ballast #6c and #6d for ss 381-434) valve details |
04-309-310 |
emergency vent valve valve cover shaft and misc. details, main ballast groups #2 and #6 and fuel ballast groups #3 and #5 |
04-311-312 |
emergency vent valve main ballast groups #2-#6 - fuel ballast groups #3-#5 handwheel, stuffing box and misc. details |
04-313-314 |
model sj sj-1 radar equipment training mechanism hull casting and misc. detail |
04-315-317 |
curves of capacity moments of inertia main ballast and safety tank |
04-318-320 |
curves of capacity, center of gravity moments of inertia trim wrt auxiliary fresh water and sanitary tank |
04-321-322 |
curves of capacity, center of gravity moments of inertia fuel oil tanks |
04-323-324 |
safety tank vent valve main and emergency arrangement |
04-325-326 |
steering gear and hydraulic system reserve oil tanks arrangement |
04-327-328 |
steering gear and hydraulic system reserve oil tank details |
04-329-330 |
mast for vertical antenna liner brackets and limit switch details |
04-331-332 |
main ballast vent valve main ballast no 1 arrangement and installation |
04-333-334 |
emergency vent valve main ballast group #4 arrangement fuel ballast group #4 |
04-335-336 |
emergency vent valve main ballast group #4 valve details fuel ballast group #4 |
04-337-338 |
model sj sj-1 radar equipment training mechanism tube and roller bearing details |
04-339-340 |
hydraulic system hydraulic control manifold detail sheet 4, 6 valve body |
04-341-342 |
hydraulic system hydraulic control manifold detail sheet 5 |
04-343-344 |
hydraulic system hydraulic control manifold detail sheet 6, 2 valve body |
04-345-346 |
hydraulic system main return manifold body |
04-347-348 |
hydraulic system main return manifold body |
04-349-350 |
hydraulic system hydraulic control manifold arrangement |
04-351-352 |
hydraulic system hydraulic control manifold detail sheet 1, 3 valve body |
04-353-354 |
hydraulic system hydraulic control manifold detail sheet 2 |
04-356-357 |
hydraulic system hydraulic control manifold detail sheet 3 |
04-357-358 |
ventilation system 12 1/4" bulkhead valves bulkhead 7 1/4" aft frame 77 arrangement |
reel 5 |
05-001-002 |
ventilation system 12 1/4" bulkhead valves, valve and valve disc, arm, lever and shaft |
05-003-004 |
ventilation system 12 1/4" bulkhead valves valve seat |
05-005-006 |
ventilation system 9"-9 1/2"-11"-8-12 1/4" bulkhead valves, levers and shafts, bulkhead 35-58-77-88-99 and 107 |
05-007-008 |
ventilation system 9"-9 1/2"-11"-8-12 1/4" bulkhead valves, operating gear bracket and latch |
05-009-010 |
ventilation system 9"-9 1/2"-11"-8-12 1/4" bulkhead valves, bulkhead 7 1/4" aft frame 77 hoods (forward) |
05-011-012 |
ventilation system 12 1/4" bulkhead valves, bulkhead 7 1/4 aft frame 77 hoods (aft) |
05-013-014 |
valve operating gear slotted lever type, hand and hydraulic assembly |
05-015-016 |
valve operating gear slotted lever type, covers, indicators and drip pan |
05-017-018 |
valve operating gear slotted lever type, frame |
05-019-020 |
valve operating gear slotted lever type, bell crank, slotted-lever and pins |
05-021 |
valve operating gear slotted lever type, cylinder and piston |
05-022-023 |
valve operating gear slotted lever type, worm, quad, shaft and hand crank |
05-024 |
1" regulator valve spring loaded stop check 3000# w.p. |
05-025 |
h.p. drain manifold 1/8"? i.p.s. |
05-026-027 |
hydraulic system 1/2" manifold |
05-028-029 |
hydraulic system main return manifold arrangement |
05-030-031 |
main and fuel ballast vents main and emergency main ballast group #2 arrangement |
05-032 |
ventilation system 9"-9 1/2"-11"-12 1/4" bulkhead valves, operating gear latch bracket |
05-033-034 |
ventilation system 11" bulkhead valve, bulkhead 9" aft frame 47 arrangements |
05-035-036 |
ventilation system hull valves operating gear positive latch assembly and details |
05-037-038 |
radio antenna system entering tube arrangement |
05-039-040 |
radio antenna system entering tube hull casting for radio room details |
05-041-042 |
radio antenna system entering tube and insulator fittings details |
05-043-044 |
ventilation system 11" bulkhead valve, bulkhead 9" aft frame 47 valve seat |
05-045-046 |
ventilation system bulkhead valve at bulkhead 9" aft frame #47 detail of hoods |
05-047-048 |
ventilation system 11" bulkhead valve, bulkhead 9" aft frame 47, disc, arm, shafts and spacers |
05-049-050 |
steering gear guide cylinder connecting rod and piston arrangement and details |
05-051-052 |
stuffing box data for hydraulic packing |
05-053-054 |
steering gear cylinder and plunger arrangement |
05-055-056 |
steering gear connecting rod and guide details sheet 2 |
05-057 |
blower positive displacement 1600 cfm ballast unloading complete assembly |
05-058 |
blower positive displacement 1600 cfm ballast unloading blind end head plate assembly |
05-059 |
blower positive displacement 1600 cfm ballast unloading gear end head plate |
05-060 |
blower positive displacement 1600 cfm ballast unloading blind end head plate |
05-061 |
blower positive displacement 1600 cfm ballast unloading gear end head plate |
05-062 |
blower positive displacement 1600 cfm ballast unloading blind end cover and cylinder |
05-063 |
blower positive displacement 1600 cfm ballast unloading impeller and shafts |
05-064 |
blower positive displacement 1600 cfm ballast unloading bolts and misc. parts |
05-065 |
blower positive displacement 1600 cfm ballast unloading gear end cover and discharge piece |
05-066 |
blower positive displacement 1600 cfm ballast unloading relief valve and inlet piece |
05-067 |
blower positive displacement 1600 cfm ballast unloading gear end parts |
05-068 |
blower positive displacement 1600 cfm ballast unloading misc. small parts |
05-069 |
blower positive displacement 1600 cfm ballast unloading bed plate |
05-070 |
blower positive displacement 1600 cfm ballast unloading oiling diagram |
05-071-072 |
steering gear power plant foundation |
05-073-074 |
bow and stern diving gear hydraulic control valve general arrangement |
05-075-076 |
main and fuel ballast vent valve arrangement main ballast groups #2-#6-#7, fuel ballast groups #3-#5 |
05-077-078 |
main and fuel ballast vent valve, valve body details, main ballast groups #2-#6-#7, fuel ballast groups #3-#5 |
05-079-080 |
main and fuel ballast vent valve, valve cover and link,?? |
05-081-084 |
bow and stern diving gear control and indicating mechanism in control room arrangement (dive station) |
05-085-087 |
stern diving gear general arrangement |
05-088-089 |
stern diving gear clutch, control cylinder and operating gear arrangement |
05-090-091 |
stern diving gear and capstan mechanism arrangement |
05-092-093 |
fuel oil water and drainage piping arrangement after battery room |
05-094-095 |
watertight door 198 lb test general arrangement welded type |
05-096-097 |
watertight door 198 lb test details of door welded type |
05-098-099 |
watertight door 198 lb test latch details welded type |
05-100-101 |
stern diving gear sprocket and bearing details |
05-102-103 |
bow and stern diving gear control mechanism operating details |
05-104-105 |
bow and stern diving gear control mechanism lever details |
05-106-107 |
bow and stern diving gear control mechanism bearing and indicator details |
05-108-109 |
bow and stern diving gear control mechanism panel details |
05-110-111 |
bow and stern diving gear indicating mechanism panel fittings details sheet no 1 (bubble clinometers) |
05-112-113 |
flats in forward torpedo room arrangement and details sheet no 1 |
05-114-115 |
flat in way of after torpedo tubes |
05-116-117 |
flats in forward torpedo room sheet 2 |
05-118-119 |
flats in motor room |
05-120-121 |
misc. tanks in aft torpedo room arrangement and details |
05-122-123 |
insulation cork |
05-124-125 |
magazine, meat and cool room |
05-126-127 |
foundations in aft torpedo room impulse air flasks and torpedo tube blow manifold |
05-128-129 |
manholes flat plate, dished plate and boiler type |
05-130 |
foundations for target bearing transmitters on bridge |
05-131 |
flush type manhole |
05-132-133 |
foundations in control room manifolds |
05-134-135 |
flagstaffs, searchlight bracket and platform, antenna outrigger, machine gun sockets and foundation for radio direction finder |
05-136-137 |
extension table wardroom |
05-138-139 |
ammunition and ordnance stowage |
05-140-141 |
draft marks |
05-142-143 |
foundations for gauge boards in control room |
05-144-145 |
foundations for gauge boards in forward and after torpedo rooms and maneuvering room |
05-146-147 |
crews quarters arrangement |
05-148-149 |
frames 36-37-38 |
05-150-151 |
frames 39-40-41 |
05-152 |
frames 42-43-44 |
05-153-154 |
frames 45-46-47 |
05-155-156 |
frames 48-49-50 |
05-157-158 |
frames 51-52-53 |
05-159-160 |
frames 54-55-56 |
05-161-162 |
frames 57-58-59 |
05-163-164 |
frames 60-61-63 |
05-165-166 |
frames 62-64-69 |
05-167-168 |
frames 65-66-67-68 |
05-169-170 |
frames 70-71-72-73 |
05-171-172 |
frames 74-75-76 |
05-173-174 |
frames 77-78-79 |
05-175 |
frames 80-81-82 |
05-176-177 |
frames 83-84-85 |
05-178-179 |
frames 86-87-88 |
05-180-181 |
frames 89-90-91 |
05-182-183 |
frames 92-93-94 |
05-184 |
frames 95-96-97 |
05-185-186 |
frames 98-99-100 |
05-187-188 |
frames 101-102-103 |
05-189-190 |
frames 104-105-106 |
05-191-193 |
portable plates control room, forward and after battery (battery loading access) |
05-194-195 |
ladders in tanks |
05-196-198 |
outer shell expansion |
05-199 |
bulkhead 10" aft of frame 55 |
05-200-201 |
bump in inner hull in way of main motors |
05-202-206 |
inner shell expansion |
05-207-208 |
compartments and tanks |
05-209-210 |
bulkhead 7 1/2" aft frame 77 |
05-211-212 |
bulkhead 3" aft frame 58 |
05-213-214 |
bulkhead at frame 88 |
05-215-216 |
holes and attachments bulkhead frame 88 |
05-217-218 |
body plan outer hull |
05-219-221 |
foundations and tanks for main and aux. generating sets |
05-222-224 |
molded offsets outer hull and superstructure fore body |
05-225-228 |
molded offset outer hull and superstructure after body |
05-229-231 |
meat and cool rooms arrangement and details |
05-232-233 |
holes and attachments bulkhead 3" aft frame 58 |
05-234-235 |
holes and attachments bulkhead 35 |
05-236-237 |
holes and attachments bulkhead 9" aft frame 47 |
05-238-239 |
holes and attachments bulkhead 7 1/4" aft frame 77 |
05-240-241 |
echo ranging and detection equipment sea valves and spider details |
05-242-243 |
holes and attachments bulkhead 107 |
05-244-246 |
top of hull and bottom of conning tower holes and attachments |
05-247 |
stowage in superstructure for boats and torpedo derrick |
05-248-250 |
platform deck officers quarters |
05-251-252 |
bulkheads nonstructural officers wc and shower forward torpedo room |
05-253-255 |
portable plates frames 84-85, 94-95, 104-105 |
05-256-257 |
access hatches frames 64 1/2 and 94 1/2. |
05-258 |
tests built in tanks and compartments |
05-259-260 |
boat and torpedo derrick kingpost foundations (forward) |
05-261 |
refrigerator officers pantry |
05-262-263 |
foundations in motor room |
05-264-265 |
holes and attachments bulkhead 13 1/2" forward frame 99 |
05-266-267 |
galley metal joiner work |
05-268 |
manhole list boiler type flat plate dished plate and flush type |
05-269 |
hot water tanks and heaters |
05-270 |
sumps secondary drainage system |
05-271-272 |
fixed lavatories and sinks with fixtures and fittings galley scullery panty and crews wash room |
05-273-274 |
diving officers check off list |
05-275-276 |
metal furniture manufactured at norfolk navy yard |
05-277-278 |
pipe berths details |
05-279 |
door and drawer locks keys and tags |
05-280-282 |
boat and torpedo derrick arrangement |
05-283-284 |
torpedo room gauge boards |
05-285-286 |
3000 lb air system hp air receiving manifold body |
05-287-288 |
3000 lb air system hp air distributing manifold body sheet no 1 |
05-289-290 |
3000 lb air system hp air hp air distributing manifold body and union ends sheet no 2 |
05-291-292 |
3000 lb air system hp air manifolds details |
05-293 |
1 regulator valve spring loaded stop check 600# w.p. |
05-294 |
hp air system air separator union ends |
05-295-296 |
18" o.d. air flask plug and drain pipe |
05-297 |
1/2" h.p. valve and hull connection (union end) |
05-298 |
3/4" h.p. valve and hull connection for air banks (silver soldered) |
05-299 |
1/2" regulator valve spring loaded stop check 3000 lbs w.p. |
05-300-301 |
standard plan h.p. valves-union ends |
05-302-303 |
magazine sprinkling system piping arrangement |
05-304-305 |
600 lb air system, m.b.t. group manifolds bodies |
05-306-307 |
600 lb air system, m.b.t. group manifolds details |
05-308-309 |
battery ventilation system cross connection fitting details |
05-310-311 |
torpedo firing system impulse air piping arrangement forward torpedo room |
05-312-314 |
air system piping arrangement forward torpedo room |
05-315-317 |
air piping arrangement officers quarters and forward battery space |
05-318-321 |
600#, 3000# and oxygen air piping arrangement control room |
05-322-324 |
10# and 225# air piping arrangement control room |
05-325-326 |
air system piping arrangement in conning tower |
05-327-328 |
air system piping arrangement in pump room |
05-329-330 |
air system piping arrangement in crews mess galley and scullery |
05-331-333 |
air piping arrangement crew quarters and after battery space |
05-334-335 |
air piping arrangement forward engine room |
05-336-338 |
air piping arrangement after engine room |
05-339-341 |
air system piping arrangement after torpedo room |
05-342-343 |
torpedo firing system impulse air piping arrangement after torpedo room |
05-344-345 |
air piping and arrangement maneuvering and motor room |
05-346-347 |
ventilation system crews quarters arrangement |
05-348-349 |
hose adapters and funnels f.o., l.o. filing systems |
05-350-351 |
5" overflow valve forward wrt tank operating gear arrangement and details |
05-352-353 |
5" overflow valve forward wrt tank arrangement and details |
05-354-355 |
salvage air system m.b.t. air connections outboard |
05-356-357 |
ventilation system 11" bulkhead valves bulkhead at frame 88 arrangement |
05-358-359 |
ventilation system 11" bulkhead valves bulkhead at 58, 88, 99 valve disc seat arm |
05-360-361 |
ventilation system 9", 9 1/2", 11", 12 1/4" bulkhead valves gears glands bushings |
05-362-363 |
ventilation system 9", 9 1/2", 11" bulkhead valves details of hoods |
05-364-365 |
ventilation system after engine room engine air supply 22" hull valve arrangement |
05-366-368 |
ventilation system ships exhaust and engine air supply 22" hull valve assembly at frame 78 |
05-369-370 |
ventilation system ships exhaust and engine air supply 22" hull valves valve disc-link and bushings |
05-371-372 |
ventilation system ships exhaust and engine air supply 22" hull valve at frame 79 valve cover |
05-373-374 |
ventilation system ships exhaust and engine air supply 22" hull valve at frame 79 valve seat |
reel 6 |
06-001-002 |
ventilation system ships exhaust and engine air supply 22" hull valves slotted link and levers |
06-003-004 |
ventilation system ships exhaust and engine air supply 22" hull valves hand lever dog and shafts |
06-005-006 |
ventilation system ships exhaust and engine air supply 22" hull valve valve seat |
06-007-008 |
ventilation system ships exhaust and engine air supply 22" hull valve hand lever dog and shafts |
06-009-010 |
ventilation system ships supply 15 1/2" hull valve foundation |
06-011-012 |
ventilation system hull valves forward engine room arrangement |
06-013-014 |
ventilation system engine air supply 15 1/2" hull valve maneuvering room arrangement |
06-015-016 |
ventilation system engine air supply 15 1/2" hull valve assembly |
06-017-018 |
ventilation system engine air supply 15 1/2" hull valve, valve seat |
06-019-020 |
ventilation system engine air supply 15 1/2" hull valve, valve seat |
06-021 |
ventilation system ships supply 15 1/2" hull valve cover |
06-022-023 |
ventilation system ships supply 15 1/2" hull valve assembly |
06-024-025 |
illegible?? |
06-026-027 |
ventilation system 11" bulkhead frame 88 and 11" bulkhead valves 13 1/2" forward frame 99 detail of hoods |
06-028-030 |
ventilation system engine air supply at frame 92 1/2 22" hull valve assembly |
06-031-032 |
ventilation system engine air supply at frame 92 1/2 hull valve cover |
06-033-034 |
ventilation system 9" and 9 1/2" bulkhead valves bulkheads 35 and 107 valve seat |
06-035 |
ventilation system 9" and 9 1/2" bulkhead valves disc and valve disc arrangements |
06-036-037 |
ventilation system 9" bulkhead valves bulkhead 35 arrangement |
06-038-039 |
ventilation system 11" bulkhead valves bulkhead 3" aft frame 58 arrangement |
06-040-041 |
ventilation system 11" bulkhead valves bulkhead 13 1/2 forward frame 99 arrangement |
06-042-043 |
ventilation system 9 1/2" bulkhead valves bulkhead 107 arrangement |
06-044-046 |
windlass and capstan wildcat and handbrake arrangement |
06-047-048 |
windlass and capstan, capstan gear case arrangement |
06-049 |
windlass and capstan, capstan gear case details |
06-050-051 |
windlass and capstan, capstan head details |
06-052-053 |
windlass and capstan, main drive bevel gear case details |
06-054 |
windlass and capstan main drive bevel gear cases arrangement |
06-055-056 |
windlass and capstan main drive bulkhead 16 gear case details |
06-057-058 |
windlass and capstan anchor chain indicator gear case details |
06-059-061 |
ventilation system air conditioning cooler casings |
06-062-064 |
fuel oil water and drainage piping arrangement forward engine room |
06-065-067 |
fuel oil water and drainage piping arrangement aft engine room |
06-068-069 |
fresh water and plumbing systems diagram |
06-070-071 |
ventilation system forward engine compartment arrangement |
06-072-073 |
fresh water and plumbing piping arrangement control room |
06-074-075 |
ventilation system after engine room arrangement |
06-076-077 |
fuel oil tanks, try cock system piping arrangement |
06-078-080 |
tank capacity gauges balanced hydraulic type plan and elevation |
06-081-082 |
ventilation system officers quarters and forward battery space arrangement |
06-083-085 |
fresh water plumbing piping arrangement crews quarters and after battery compartment |
06-086-087 |
freshwater and plumbing piping arrangement forward engine room |
06-088-089 |
freshwater and plumbing piping arrangement after engine room |
06-090 |
ventilation terminals |
06-091-092 |
ventilation system engine room details |
06-093-095 |
air-oil-water and vent systems piping in superstructure forward of frame 70 |
06-096-098 |
air-oil-water and vent systems piping in superstructure aft of frame 69 |
06-099-100 |
fresh water and plumbing system - special fitting |
06-101-102 |
fresh water and plumbing system general arrangement crews mess galley and scullery |
06-103-105 |
piping in outside tanks forward |
06-106-108 |
piping in outside tanks aft |
06-109-110 |
air system special fittings |
06-111-112 |
water tight door 198lb test gear details welded type |
06-113 |
water tight door 198lb test fixed dead light welded type |
06-114-115 |
water tight door 198lb test door frame details welded type door |
06-116-118 |
ventilation system 36" supply exhaust and induction valve (outboard) arrangement |
06-119-120 |
ventilation system 36" supply exhaust and induction valve (outboard) yoke shaft block and gag - socket |
06-121-122 |
ventilation system 36" supply exhaust and induction valve (outboard) hull casting and streamline plate |
06-123-124 |
ventilation system 36" supply exhaust and induction valve valve outboard trunk |
06-125-126 |
ventilation system 36" supply exhaust and induction valve outboard spindle and lever bearing and gag - wrench |
06-127-128 |
ventilation system 36" supply exhaust and induction valve outboard operating gear hand and hydraulic arrangement |
06-129-130 |
ventilation system 36" supply exhaust and induction valve outboard operating gear frame |
06-131-132 |
ventilation system 36" supply exhaust and induction valve outboard operating gear cylinder and piston |
06-133-134 |
ventilation system 36" supply exhaust and induction valve outboard operating gear lever slotted link and pins |
06-135-136 |
ventilation system 36" supply exhaust and induction valve outboard operating gear hand crank and gears |
06-137-138 |
ventilation system 36" supply exhaust and induction valve outboard operating gear, gear casing and covers |
06-139-140 |
ventilation system 36" supply exhaust and induction valve outboard, operating gear indicator and drip pan |
06-141-142 |
windlass and capstan chain compressor gear case details |
06-143-144 |
windlass and capstan hydraulic operating mechanism arrangement |
06-145-146 |
stern diving gear hydraulic system flanges and special fittings |
06-147-148 |
stern diving gear hydraulic piping arrangements in after torpedo room |
06-149-151 |
m.f.b. and safety tank vent valve operating gear arrangement 3 3/4" d x 3 1/2" and 3 1/2" cylinders |
06-152-153 |
main fuel ballast and safety tank vent valve operating gear frame details |
06-154-155 |
m.f.b. and safety tank vent valve operating gear crosshead and link detail |
06-156-157 |
m.f.b. and safety tank vent valve operating gear hand lever and miscellaneous details |
06-158-159 |
bow and stern diving gear indicating mechanism panel fittings details sheet number 2 ** |
06-160-161 |
watertight door gun access trunk-30" circular door frame details |
06-162-163 |
model sj radar equipment training mechanism clutch arrangement and details |
06-164 |
watertight doors list |
06-165-166 |
foundation for sea water circulating pump |
06-167-168 |
platform deck maneuvering room |
06-169-170 |
foundation for number 1 and 2 periscopes and vertical antenna mast motor hoists |
06-171-172 |
model sj radar equipment training mechanism clutch details |
06-173-174 |
ventilation system 11" bulkhead valves bulkhead 9" aft frame 47 gears bracket and levers |
06-175-176 |
model sj radar equipment training mechanism upper bevel gear case assembly and details |
06-177 |
antenna bowl details |
06-178-179 |
ventilation system 11" bulkhead valves bulkhead 9" aft frame 47 housing |
06-180-181 |
model sj radar equipment training mechanism lower bevel gear case arrangements and details |
06-182-183 |
number 1 and 2 periscopes sheave and bracket details |
06-184-185 |
model sj radar equipment training mechanism drip pan and miscellaneous details |
06-186-187 |
toroidal hydrophone shaft and stuffing box details |
06-188 |
blower positive displacement 1600 cfm ballast unloading complete unit outline |
06-189 |
oil guard high pressure compressor, hardie-tynes |
06-190-191 |
type foundation plan for small gauge boards and misc. single gauges |
06-192-193 |
hardie-tynes, sectional assembly outline and specs, 25 sl drip proof semi enclosed sv motor for high pressure air compressor |
06-194 |
hardie-tynes, gage board and air strainer high pressure air compressor |
06-195 |
hardie-tynes, general assembly of air gage lubricator piping and valves high pressure air compressor |
06-196 |
hardie-tynes, first stage unloading valve and valve bonnets high pressure air compressor |
06-197 |
hardie-tynes, water pump details, high pressure air compressor |
06-198 |
hardie-tynes, water pump details, high pressure air compressor |
06-199 |
hardie-tynes sectional view of compressor, high pressure air compressor |
06-200 |
hardie-tynes air piping details high pressure air compressor |
06-201 |
hardie-tynes first and second intercoolers high air air compressor |
06-202 |
hardie-tynes 1st and 2nd cylinder inlet and discharge valves high pressure air compressor |
06-203 |
hardie-tynes 3rd and 4th stage inlets and discharge valve high pressure air compressor |
06-204 |
hardie-tynes outside view of compressor motor high pressure air compressor |
06-205 |
hardie-tynes center frame high pressure air compressor |
06-206 |
hardie-tynes combined assembly of air water and oil piping high pressure air compressor |
06-207 |
hardie-tynes diagrammatic sketches of air water and control piping high pressure air compressor |
06-208 |
hardie-tynes third intercooler high pressure air compressor |
06-209 |
hardie-tynes spare parts list high pressure air compressor |
06-210 |
hardie-tynes parts and drawing reference list high pressure air compressor |
06-211 |
hardie-tynes parts and drawing reference list and wrenches high pressure air compressor |
06-212 |
sectional assembly and outline and specs d-204 d.p. semi-encl. self vent motor for battery ventilation set |
06-213 |
sectional assembly and outline and specs d-326 d.p. semi-encl. self vent motor for drainage pump |
06-214 |
sectional assembly and outline and specs d-365 d.p. semi-encl. self vent motor for trimming pump |
06-215-216 |
d.c. magnetic controller for high pressure air compressor |
06-217-218 |
bull 515, 13" disc brake |
06-219 |
sectional assembly and outline and specs d-326 d.p. semi-encl. self vent motor for hull ventilation supply fan |
06-220-221 |
d.c. magnetic controller for periscope and vertical antenna hoist |
06-222 |
sectional assembly and outline and specs d-324 d.p. semi-encl. self vent motor for hull ventilation exhaust fan |
06-223-224 |
d.c. magnetic controller for hull ventilation fan motors |
06-225 |
padlocks and key tags |
06-226-228 |
metal joiner doors |
06-229-230 |
chart table in conning tower |
06-231-232 |
foundations in forward torpedo room sheet number 3 |
06-233 |
sound isolation foundations for battery ventilation sets |
06-234-235 |
access hatch and cover to cool room |
06-236-238 |
bulkhead non-structural galley and mess room |
06-239 |
sound isolation foundations for fan motors hull ventilation system |
06-240-242 |
bilge keels and stringers |
06-243-244 |
torpedo handling derrick details |
06-245 |
torpedo derrick rigging |
06-246 |
torpedo handling metal blocks |
06-247-248 |
bulkheads non-structural radio room and storeroom |
06-249-250 |
typewriter desk in office |
06-251-252 |
periscope and vertical antenna wells |
06-253-254 |
portable stowage benches |
06-255-257 |
main and fuel ballast vents main and emergency fuel ballast group #5 and main ballast group #6 arrangement |
06-258-259 |
main and fuel ballast vents main and emergency fuel ballast group #3 arrangement |
06-260-261 |
torpedo and mine handling and stowage forward and aft lashing strap saddles details |
06-262-263 |
torpedo and mine handling and stowage forward and aft lashing strap details |
06-264-265 |
after torpedo room arrangement |
06-266-267 |
emergency vent valve main ballast #6a and #6b arrangement |
06-268-269 |
vent valve mb #6a and #6b valve details |
06-270-271 |
emergency vent valve main ballast groups #2 and #6c-6d, fuel ballast groups #3-#5 arrangements |
06-272-273 |
main and fuel ballast vent valves mb #2a-#2b-#2c-#2d, fb #3a-#3b-#5a-#5b foundations |
06-274-275 |
main, fuel, ballast and safety tank vent valve operation gear foundations |
06-276-277 |
main engine exhaust system hull liners |
06-278-280 |
bow diving gear arrangement forward |
06-281-282 |
bow diving gear flanges and special fittings |
06-283-284 |
bow diving gear rigging interlock valve and bracket details |
06-285-286 |
bow diving gear rigging gear inboard arrangement |
06-287-288 |
bow diving gear rigging and windlass worm gear and clutch details |
06-289-290 |
bow diving gear hydraulic piping arrangement forward |
06-291-292 |
bow diving gear tiller links plane stock details |
06-293-294 |
bow diving gear guide bearings |
06-295-296 |
bow diving gear tilting piston - piston rod etc. |
06-297-298 |
bow diving gear tilting cylinder details |
06-299-300 |
bow diving gear arrangement of tilting gear in forward torpedo compartment |
06-301-302 |
bow diving gear tilting indicator arrangement and details |
06-303-304 |
bow diving gear rigging gear shaft and hull fittings details |
06-305-306 |
bow diving gear rigging indicator and valve operating gear misc. details |
06-307-308 |
bow diving gear tilting control cylinders and power plant assembly |
06-309-310 |
bow diving gear rigging gear worm gear case details |
06-311-312 |
bow diving gear rigging and windlass clutch details |
06-313-314 |
bow diving gear rigging interlock valve operating cams, and misc. details |
06-315-316 |
hull opening indicator system contact maker operating mechanism cr space, engine room, aft torpedo room, conning tower hatch arrangement and details |
06-317-318 |
bow buoyancy vent valve operating gear frame details |
06-319-320 |
bow buoyancy vent valve operating gear cylinder and piston details |
06-321-322 |
bow buoyancy vent valve operating gear crosshead and link details |
06-323-324 |
bow buoyancy vent valve operating gear foundations and misc. details |
06-325-326 |
bow buoyancy vent valve operating gear arrangement |
06-327-328 |
main and fuel ballast vent valves safety tank foundations |
06-329-330 |
stern torpedo tubes and steering gear greasing arrangement |
06-331-332 |
stern torpedo tubes and steering gear greasing details |
06-333-334 |
windlass and bow rigging control and change valves arrangement |
06-335-336 |
windlass and bow rigging controls and change valves body details |
06-337-338 |
windlass and bow rigging controls and change valves cover and piston details |
06-339-340 |
windlass and capstan control shaft details |
06-341-342 |
main fuel ballast and safety tank vent valve operating gear cylinder and piston |
06-343-344 |
manifold ballast and safety tank vent valve operating gear cylinder and piston details |
06-345 |
no 1 and 2 periscopes brackets foundation details in conning tower |
06-346-347 |
no 1 and 2 periscopes hull casting |
06-348-350 |
water and drainage piping arrangement pump room |
06-351-352 |
no 1 and 2 periscopes upper limit switch arrangement and details |
06-353-354 |
emergency vent valve main ballast #6a and #6b duct details |
06-355 |
flood valves safety tank arrangement at frame 63 port and starboard |
06-356-357 |
no 1 and 2 periscopes general arrangement |
06-358-360 |
watertight doors stops and catches for wide open positions arrangement |
06-361 |
ventilation system engine air supply 15 12" hull valve cover |
06-362 |
bow torpedo tubes bulkhead grease manifold and greasing details |
06-363-364 |
signal ejector breech mechanism details |
06-365 |
2 1/2 /2a3uhx de laval imo pump outline and assembly, 29 gpm hydraulic system pump |
06-366 |
2 1/2 /2a3uhx de laval imo pump details, 29 gpm hydraulic system pump |
reel 7 |
07-001 |
2 1/2 /2a3uhx de laval imo pump details |
07-002-003 |
bow torpedo tubes greasing arrangement |
07-004-005 |
hydrophone for jp-1 sound apparatus general arrangement |
07-006-007 |
hydrophone for jp-1 sound apparatus foundations details |
07-008-009 |
signal ejector arrangement in ship |
07-010-011 |
hull opening indicator system contact maker operating mechanism gun access and forward escape hatch arrangement and details |
07-012 |
lathe foundation maneuvering room |
07-013-014 |
torpedo tube shutters forward upper arrangement and lines |
07-015-016 |
torpedo tube shutters forward middle arrangement and lines |
07-017-018 |
torpedo tube shutters forward lower arrangement and lines |
07-019-020 |
forward torpedo tube shutters details of upper shutters |
07-021-022 |
torpedo tube shutters middle and lower details |
07-023 |
foundations for cooler casings hull ventilation system |
07-024 |
sound isolation for lube oil stand by pump in motor room |
07-025-027 |
air induction and ventilation piping outboard |
07-028-029 |
storage battery ventilation air supply ducts |
07-030-031 |
superstructure sides and main deck frames 45-66 incl. |
07-032-034 |
superstructure sides and main deck frames 66 to 125 incl. |
07-035-036 |
superstructure frames 56 to 67 incl. |
07-037-038 |
superstructure frames 68 to 79 incl. |
07-039-040 |
superstructure frames 80 to 91 incl. |
07-041-042 |
superstructure frames 92 to 108 incl. |
07-043-044 |
hatch davit (portable) location details installation |
07-045-046 |
main deck wood |
07-047-048 |
main deck wood details |
07-049-051 |
ordnance ready service lockers - control room and officers quarters |
07-052-053 |
ladders and grabs forward and after engine rooms |
07-054-055 |
sea connections seawater circ. systems main and aux engines and motors |
07-056-057 |
lead ballast stowage |
07-058-059 |
foundation for stern diving gear and capstan worm gear case |
07-060-061 |
foundations in aft engine room sheet 1 |
07-062-064 |
foundations in forward engine room sheet 1 |
07-065-066 |
main engine muffler foundations and induction valve lever bearing foundation |
07-067-068 |
torpedo handling and stowage forward deck skid arrangement and details |
07-069-070 |
sound isolation for ac motor generators in maneuvering room |
07-071-072 |
outboard fittings general arrangement |
07-073-074 |
sounding rods for lubricating oil tanks and clean fuel oil tank |
07-075-076 |
foundations for oxygen flasks |
07-077-078 |
foundation for bow diving tilting power plant and interlock valve |
07-079-080 |
foundations in after engine room sheet 2 |
07-081-083 |
foundations in forward engine room sheet 2 |
07-084-085 |
foundations for gauge boards in forward and after engine rooms |
07-086-087 |
berths and lockers numbering |
07-088-089 |
sound isolation foundation for drain pump in pump room |
07-090 |
list of foundations for small gauge boards and misc. single gauges |
07-091-092 |
foundation for gauge boards in pump room |
07-093-095 |
pressure proof ready service lockers and loading frames for 20 mm magazines and dip pots |
07-096-097 |
conning tower fairwater and bridge elevation and plans |
07-098 |
foundations for bow diving gear rigging mechanism |
07-099-100 |
conning tower fairwater and bridge - molded lines and offsets |
07-101-102 |
lines molded offsets main deck |
07-103-104 |
bulkheads nonstructural officers and cpo quarters |
07-105-106 |
conning tower fairwater and bridge sections |
07-107-108 |
conning tower fairwater and bridge joiner work gratings |
07-109-110 |
foundations for controllers and electrical equipment pump room port side |
07-111 |
stowage for manilla rope, deck gear and towing equipment in superstructure |
07-112 |
main shafting fairwaters at stern tubes |
07-113-114 |
foundations for radio motor generator set, 200# auxiliary air compressor, rotary converter and work bench in pump room |
07-115 |
label plates inside |
07-116-117 |
lockers in forward torpedo room arrangement and details |
07-118 |
metal joiner door list |
07-119-120 |
crews mess tables |
07-121-122 |
foundations for supports for periscopes, vertical antenna mast and radar |
07-123-124 |
medical locker |
07-125 |
log desk in engine rooms |
07-126-127 |
curves of capacity c of g and moment of inertia lube oil tanks |
07-128-130 |
compartment and access |
07-131-133 |
superstructure sides and main deck frames 10 to 45 incl. |
07-134-135 |
storerooms below platform deck |
07-136-137 |
lockers in after torpedo room arrangement and details |
07-138-139 |
foundation for diving gear control and indicating mechanism in control room |
07-140 |
base for underwater sound motor generator (reinforcement) |
07-141-142 |
gang plank arrangement and details |
07-143-144 |
lockers in crews quarters arrangement and details |
07-145-146 |
mess gear stowage in mess benches |
07-147-148 |
platform deck control room |
07-149-150 |
sliding berth details |
07-151-152 |
berthing in crews quarters arrangement and details |
07-153-154 |
marker buoys forward and aft installation in superstructure and releasing mechanism sheet no. 1 |
07-155-156 |
marker buoys forward and aft installation in superstructure and releasing mechanism sheet no. 2 |
07-157-158 |
foundations high pressure air compressors and motors |
07-159-160 |
work bench and log desk in maneuvering room |
07-161 |
miscellaneous tanks and foundations (ventilation air cooler) |
07-162-163 |
sound isolation air compressor ?? |
07-164 |
foundations for controllers pump room starboard side |
07-165 |
crews toilet boxes |
07-166-167 |
foundations for motor generators for wca-2 system and gyro motor generators in pump room |
07-168 |
deck clamps for muzzle and breech covers - 4 inch mount mark xi mods 38 to 42 incl. (50 cal. wet mount) |
07-169-170 |
misc. lockers and stowage in forward torpedo room |
07-171-172 |
misc. lockers and stowage in after torpedo room |
07-173-174 |
misc. lockers and stowage in conning tower |
07-175-176 |
foundations for accumulator and accumulator air flask |
07-177-178 |
foundations in pump room |
07-179 |
misc. metal joiner details |
07-180-181 |
hydraulic system piping arrangement forward torpedo room |
07-182-183 |
hydraulic system piping arrangement officers quarters |
07-184-185 |
hydraulic system piping arrangement control room |
07-186-187 |
hydraulic system piping arrangement crews mess etc. |
07-188-189 |
hydraulic system piping arrangement crews space |
07-190-191 |
hydraulic system piping arrangement forward engine room |
07-192-193 |
hydraulic system piping arrangement after engine room |
07-194-195 |
hydraulic system piping arrangement after torpedo room |
07-196-197 |
hydraulic system piping arrangement maneuvering room |
07-198-199 |
ventilation system maneuvering and motor rooms arrangement |
07-200-201 |
fuel oil, water and drainage special fittings |
07-202-203 |
hull and deck fittings salvage air fuel and lubrication oil systems |
07-204 |
200# air muffler |
07-205-206 |
fuel oil water drainage piping arrangement crews mess, galley, scullery |
07-207 |
ventilation system sound isolation molds for rubber spools forward engine room |
07-208 |
manifold 4 valve 1/4" size blow and vent |
07-209-210 |
ventilation system control room, ct and pump room arrangement |
07-211 |
h.p. system 1" strainer |
07-212-213 |
air system special fittings sheet 1 |
07-214-215 |
sound isolation refrigeration and air conditioning circulating water pumps and motors in pump room |
07-216-217 |
hydraulic system main engine outside exhaust piping arrangement engine room |
07-218 |
hydraulic system main engine outside exhaust valve special fittings |
07-219-220 |
target designation system circuits 1gt, 2gt, 7gt, 1pd and 2pd elementary wiring diagram |
07-221 |
target designation system circuits 1gt, 2gt, 7gt, 1pd and 2pd isometric wiring diagram |
07-222 |
swing check valve 2" nominal size |
07-223 |
trim pump vertical and horizontal drive electrode drip shield base and cover |
07-224-225 |
drain pump vertical and horizontal drive electrode drip shield base and cover |
07-226-227 |
propellor |
07-228-229 |
hydrophone for jp-1 sound apparatus, upper bearing assembly and details |
07-230-231 |
hydrophone for jp-1 sound apparatus worm gear and case assembly and details |
07-232-233 |
d.c. magnetic controller for salt water feed pump |
07-234-235 |
illegible ?? |
07-236-237 |
torpedo heating switch and indicator panel and station assembly and details |
07-238-239 |
torpedo charging and heating panel assembly and details |
07-240-241 |
torpedo heating switch and indicator panel - 4 station assembly and details |
07-242-243 |
torpedo heating indicator panel, 2 stations and 5 station assembly and details |
07-244 |
mark 18 torpedo heating connection receptacle and plug and batter plug sheath |
07-245 |
main shafting rubber covering stern tube shaft details |
07-246-247 |
main shafting bearings stern tube strut stuffing box |
07-248-250 |
main shafting arrangement |
07-251-252 |
main motor reduction gear and propellor shaft turning and locking arrangement and details |
07-253 |
main shafting forging details |
07-254-255 |
propellor shaft and coupling details |
07-256 |
2" strainer by-pass valve lube oil system motor room |
07-257 |
special 2" valve lube oil system motor room |
07-258 |
special oil heater for lubrication oil general assembly and outline |
07-259-260 |
circulating sea water system mach. compartments diagram |
07-261-262 |
2 1/2" temperature control valve seawater circulation system motor room |
07-263-264 |
8" sea suction valves arrangement and details sea water circulating system engine rooms |
07-265-266 |
fresh water system piping diagram |
07-267-268 |
sea water circ. system motor room piping arrangement |
07-269 |
sea water circ. system sea valve 4" nominal size motor room |
07-270 |
sea water circ. system motor room strainer 3" nominal size |
07-271 |
special valves 1" nominal size stern tube flushing motor room sea water circulating system |
07-272-273 |
special 1 1/4" and 1" manifold sea water circulating system engine room |
07-274 |
leslie-tyfon whistle, whistle and operating valve a-200-l for submarine service |
07-275 |
sea water circulating system - motor room special fittings |
07-276-277 |
sea water circulating system motor room manifold 1 1/2 nominal size |
07-278 |
fresh water tank and receiver arrangement and details distilling system forward engine room |
07-279 |
brine tank and receiver arrangement and details distilling system forward engine room |
07-280 |
1" special angle valve distilling system |
07-281 |
vent damper vapor compression type distilling system |
07-282 |
refrigerating plant circulating sea water 3" macomb strainer |
07-283 |
refrigeration plants circulating sea water 3" special sea valve |
07-284-285 |
special fittings for refrigerating and circulating water system |
07-286-287 |
submarine fuse test panel |
07-288-289 |
switch panel for lube oil heater assembly |
07-290-291 |
switch panel for lube oil heater details |
07-292-293 |
propulsion control group enclosure |
07-294-295 |
main power system motor and generator connections details |
07-296-298 |
main power system motor and generator connections cable arrangement in motor room |
07-299-300 |
main battery disconnect switch operating gear arrangement |
07-301-302 |
main battery disconnect switch operating gear details |
07-303-304 |
main storage batteries ventilation below platform deck and walking flat |
07-305 |
door operated light switch for refrigerator arrangement and details of operating gear |
07-306 |
dimmer rheostat for periscope lights assembly and details |
07-307 |
shaft revolution indicator system circuit k rotary converter type rl-152 |
07-308 |
underwater log general arrangement |
07-309 |
underwater log master transmitter indicator |
07-310 |
underwater log rodometer assembly |
07-311 |
underwater log speed and distance indicator 0-25 knots |
07-312 |
underwater log master transmitter indicator interior unit 0-25 knots |
07-313 |
underwater log master transmitter indicator main force and balance arm assembly 0-25 knots |
07-314 |
underwater log master transmitter indicator component force driving and follower assembly 025 knots |
07-315 |
underwater log master transmitter indicator speed and distance transmission assembly |
07-316 |
two speed power motor - bendix underwater log |
07-317 |
air collector- bendix underwater log |
07-318 |
bendix underwater log pressure static bellows assembly 0-25 knots |
07-319 |
bendix underwater log speed and distance indicator interior unit |
07-320 |
bendix underwater log autosyn motor type flange mounted |
07-321 |
bendix underwater log autosyn generator |
07-322 |
bendix underwater log autosyn motor indicator with damper |
07-323-324 |
2" dia voice tube system bridge to conning tower arrangement and details |
07-325 |
collision diving and general alarm circuits cd, gd and g |
07-326 |
contact maker type c assembly and details for direction warning for engine telegraph |
07-327 |
submarine marker buoy telephone and light outlet unit inside of hull assembly |
07-328 |
submarine marker buoy telephone and light outlet unit inside of hull details sheet no. 1 |
07-329 |
rudder and plane angle indicator system elementary and isometric wiring diagrams circuit n, nb and ns |
07-330-331 |
engine and motor order telegraph system main motor direction warning contact makers |
07-332-333 |
i.c. system - circuit tr, 2 dial indicator for hull opening assembly and detail |
07-334 |
motor order telegraph system isometric wiring diagram circuits 1mb and 2 mb |
07-335-336 |
engine control indicator system indicator with repeat back assembly and wiring diagrams circuit 3mb |
07-337-338 |
engine control indicator system indicator with repeat back circuit 3mb details |
07-339-340 |
ic system engine control indicator system transmitter for maneuvering room assembly circuit 3mb |
07-341-342 |
engine control indicator system transmitter for maneuvering room details no 1 circuit 3mb |
07-343-344 |
engine control indicator system transmitter for maneuvering room details no 2 circuit 3mb |
07-345-346 |
engine control indicator system transmitter for maneuvering room detail no 3 circuit 3mb |
07-347-348 |
underwater log housing gear upper bearing details |
07-349-350 |
underwater log housing gear lower bearing details |
07-351-352 |
underwater log housing gear arrangement |
07-353-354 |
underwater log housing gear crank guide clamp and misc. details |
07-355-356 |
stern diving gear auxiliary tilting indicator transmitter 6 volt |
07-357-358 |
bow and stern plane aux. tilting 7 light indicator and isometric wiring diagram 6 volt |
07-359-360 |
recognition signal board |
07-361-362 |
water level indicator system and trim and drain pump air domes assembly details and elementary |
reel 8 |
08-001 |
telephone panel sound powered type 25 line toggle switch type |
08-002-003 |
radio antenna system arrangement and details |
08-004-005 |
radio and sound system wiring deck plans |
08-006-007 |
echo ranging and detection equipment general arrangement |
08-008-009 |
echo ranging and detection equipment hydraulic control valve assembly and details |
08-010-011 |
echo ranging and detection equipment upper drift stop arrangement and details |
08-012-013 |
echo ranging and detection equipment ?? arrangement |
08-014 |
echo ranging and detection equipment piston rod head and misc. details |
08-015-016 |
echo ranging and detection equipment hydraulic control mechanism control valve and misc. details |
08-017-018 |
echo ranging and detection equipment training gear details |
08-019-020 |
echo ranging and detection equipment piston, piston rod etc. |
08-021 |
echo ranging and detection equipment projector tube head and azimuth details |
08-022-023 |
echo ranging and detection equipment assembly section of projector tube and cylinder |
08-024-025 |
echo ranging and detection equipment housing |
08-026-027 |
echo ranging and detection equipment arrangement above torpedo room flat |
08-028-029 |
echo ranging and detection equipment contact makers for indicator lights arrangement and details |
08-030 |
echo ranging and detection equipment gimbal ring and misc details |
08-031 |
echo ranging and detection equipment power training unit arrangement |
08-032 |
echo ranging and detection equipment fairlead for projector cable arrangement and details |
08-033-034 |
echo ranging and detection equipment projector heads keyways and identification marks |
08-035-036 |
echo ranging and detection equipment emergency hand training gear handwheel shafts and misc. details |
08-037-038 |
echo ranging and detection equipment emergency hand training gear stop cylinder clutch and misc. details |
08-039-040 |
echo ranging and detection equipment - listening system, model wca and wca-1 equipment arrangement in forward torpedo room |
08-041-042 |
echo ranging and detection equipment emergency hand training gear assembly |
08-043-044 |
echo ranging and detection equipment emergency hand training gear clutch lever and misc. details |
08-045-046 |
echo ranging and detection equipment lower drift stop arrangement and details |
08-047-048 |
echo ranging and detection equipment lower drift stop location arrangement |
08-049-050 |
echo ranging and detection equipment circuit s-es arrangement in ship diagram and ext. wiring diagrams |
08-051-052 |
model wca echo ranging listening sounding equipment cir s-rc power training diagrammatic and ext. wiring diagrams |
08-053-054 |
model wca echo ranging listening sounding equipment cir s-er external wiring diagram |
08-055-056 |
echo ranging and detection equipment dirt shield |
08-057-058 |
torpedo fire control system isometric wiring diagram circuit ga and gt |
08-059 |
connection box for torpedo firing solenoid assembly and details |
08-060-061 |
torpedo ready light, battle order and firing system wiring diagram circuits |
08-062-063 |
aux. engine gauge board below deck valve and piping arrangement aft engine room |
08-064 |
special valve arrangement and details gauge boards 1/4" od tubing |
08-065-066 |
torpedo derrick aft stress diagram and data |
08-067-068 |
boat and torpedo derrick forward stress diagram and data |
08-069-070 |
foundations for liquidometers |
08-071-072 |
windlass and capstan greasing arrangement |
08-073-074 |
steering gear pump control centering mechanism arrangement and details |
08-075-076 |
stern diving gear stern plane drift stop arrangement and details |
08-077-078 |
drying locker for binoculars |
08-079 |
ventilation system 15 1/2" and 22" hull valves substitute detent spring assembly and details |
08-080-081 |
auxiliary engine exhaust system 8" inside exhaust valve gate type valve body and seat |
08-082 |
special 2" gooseneck valves lube oil system engine rooms |
08-083 |
3 / 2 1/2" a32n de laval imo pump outline and assembly motor driven lube oil pump for main reduction gears standby and transfer service |
08-084 |
3 / 2 1/2" a32n de laval imo pump motor driven lube oil pump for main reduction gears standby and transfer service details |
08-085 |
3 / 2 1/2" a32n de laval imo pump details |
08-086 |
3 / 2 1/2" a32n de laval imo pump motor details |
08-087 |
dc magnetic controller resistance type for main motor and reduction gear standby lube oil pump |
08-088 |
dc motor assembly |
08-089-090 |
refrigerant system air conditioning - refrigeration diagram |
08-091-092 |
model sj-1 radar equipment training mechanism ppi general arrangement |
08-093-094 |
model sj-1 radar equipment training mechanism ppi arrangement of lower end |
08-095-096 |
model sj-1 radar equipment training mechanism ppi bearing and indicator foundation and clutch arrangement |
08-097-098 |
torpedo and mine handling and stowage forward and aft portable chock for torpedo |
08-099 |
lathe drive motor |
08-100 |
dc manual control equipment for motor driven engine lathe |
08-101 |
14" sebastion engine lathe |
08-102-103 |
reel for submarine escape ascending line |
08-104-105 |
air conditioning in conning tower piping arrangement |
08-106-107 |
hydraulic system accumulator indicator |
08-108-109 |
main battery disconnect switch operating gear gear case and details |
08-110-111 |
foundation for 3"/50-5"25 caliber pressure proof ready service locker |
08-112 |
foundations for trim pump priming valve and taylor aneroid manometer |
08-113-114 |
motor room machinery arrangement |
08-115 |
main reduction gear drive sa-111, master drawing, spare parts and tool list |
08-116 |
main storage battery type owtx-49b cell list of plans |
08-117 |
echo range and detector transmitter |
08-118 |
autosyn generator |
08-119-122 |
ready service locker |
08-123-124 |
gun muzzle support |
08-125 |
signal flare brackets and operating gear |
08-126-127 |
oxygen system diagram |
08-128 |
foundation for after 20 mm magazine locker |
08-129-131 |
bridge arrangement |
08-132-133 |
cross curves of stability |
08-134 |
grove regulator air pressure reducing valve n-406 alt 0 |
08-135 |
grove regulator air pressure reducing valve n-407 alt 0 |
08-136 |
grove regulator oil pressure reducing valve n-409 alt 0 |
08-137 |
grove regulator air pressure reducing valve n-408 alt 0 |
08-138-139 |
dc magnetic controller for vapor compression still |
08-140 |
york ice machine, air conditioning plant sectional assembly |
08-141-142 |
york ice machine, air conditioning plant general arrangement |
08-143-144 |
york ice machine, air conditioning plant crankcase and details |
08-145-146 |
york ice machine, air conditioning plant cylinder |
08-147-148 |
york ice machine, air conditioning plant piston and suction valve |
08-149-150 |
york ice machine, air conditioning plant connecting rod |
08-151-152 |
york ice machine, air conditioning plant gaskets and stop valves |
08-153 |
york ice machine, air conditioning plant compressor fitting and piping details |
08-154-155 |
york ice machine, air conditioning plant top head and discharge valve plate |
08-156-157 |
york ice machine, air conditioning plant list of material, spare parts and tools |
08-158 |
york ice machine, air conditioning plant 2 5/8" sectional assembly |
08-159 |
york ice machine, air conditioning plant 2 5/8" general arrangement |
08-160-161 |
york ice machine, air conditioning plant 2 5/8" crank case and details |
08-162-163 |
york ice machine, air conditioning plant 2 5/8" crankshaft flywheel motor pulley and shaft seal |
08-164 |
york ice machine, air conditioning plant 2 5/8" cylinder |
08-165-166 |
york ice machine, air conditioning plant 2 5/8" top head and discharge valve plate |
08-167-168 |
york ice machine, air conditioning plant 2 5/8" piston connecting rod and suction valves |
08-169-170 |
york ice machine, air conditioning plant 2 5/8" details of suction manifold |
08-171-172 |
york ice machine, air conditioning plant 2 5/8" details of discharge manifold |
08-173-174 |
york ice machine, air conditioning plant 2 5/8" assembly and details of manifold |
08-175-176 |
york ice machine, air conditioning plant 2 5/8" gaskets oil sight pins and cap screws |
08-177 |
york ice machine, air conditioning plant 2 5/8" list of material spare parts and tools |
08-178-179 |
refrigeration plant, condenser, receiver |
08-180 |
refrigeration plant, ice cube maker and trays |
08-181-182 |
refrigeration plant, meat and cool room coils |
08-183-184 |
refrigeration plant, high and low pressure cutout and thermostat |
08-185-186 |
refrigeration plant, condenser and receiver |
08-187 |
refrigeration plant, suction pressure control valve solder joint ends |
08-188-189 |
refrigeration plant, high and low pressure circuit and thermometer |
08-190-191 |
refrigeration plant, arrangement of freon 12 mains |
08-192 |
refrigeration plant air conditioning dehydrators tube expander and flaring tool |
08-193-194 |
refrigeration plant air conditioning plant thermometers and gauges |
08-195 |
refrigeration plant air conditioning freon 12 angle stop valves and angle expansion valves |
08-196 |
air conditioning plant fin cooling coil assembly and details |
08-197 |
field rheostats for submarine equipment |
08-198-199 |
echo ranging and detection equipment trunk cover, etc. |
08-200-201 |
torpedo ready light, battle order and firing system isometric wiring diagram circuits gpa and gr |
08-202-203 |
torpedo fire control wiring deck plan (including battle telephone) |
08-204-205 |
torpedo and mine handling and stowage aft work table arrangement and details |
08-206-207 |
aux. motors starting resistance enclosures |
08-208 |
foundation for low pressure blower in pump room |
08-209-210 |
shock mounting for main propulsion control |
08-211 |
foundations from magnetic compasses in conning tower and control room |
08-212-213 |
seats in conning tower |
08-214 |
diesel fuel and diesel lubrication oil purifier outline |
08-215-216 |
diesel fuel and diesel lubrication oil purifier assembly |
08-217-218 |
diesel fuel and diesel lubrication oil purifier details |
08-219-220 |
diesel lubricating oil purifier pump assembly outline and details |
08-221-222 |
sectional view assembly and material list for 900 gph lube oil purifier or service pump |
08-223-224 |
details of 900 gph lube oil purifier or service pump |
08-225-226 |
sectional view assembly and material list for 600 gph fuel oil transfer and purifier pump |
08-227-228 |
details of 600 gph fuel oil transfer or purifier pump |
08-229-230 |
air conditioning plant, automatic liquid control manifold with packless manually operated bypass valves |
08-231-232 |
regulator control panel for dc ac motor generator set |
08-233-234 |
generator voltage regulator |
08-235-236 |
generator voltage regulator schematic |
08-237 |
sectional assembly and specs. motor for diesel lube oil purifier or service pump |
08-238 |
sectional assembly and specs. motor for air conditioning circulating water pump |
08-239 |
sectional assembly and specs. for dc/ac motor generator set |
08-240 |
bill of materials, spare parts and specs. for dc/ac motor generating set |
08-241-242 |
dc magnetic controller for air-conditioning equipment |
08-243 |
sectional assembly and specs for motor for diesel lube oil purifier |
08-244 |
sectional assembly and specs motor for fuel oil transfer & purifier pump |
08-245 |
sectional assembly and specs motor for diesel fuel oil purifier |
08-246-247 |
automatic speed regulator for dc/ac motor generator set |
08-248-249 |
type hir voltage regulator for dc lighting feeder |
08-250 |
shaft revolution indicator system circuit k transmitter gear details |
08-251 |
signal generator for submarine announcing equipment (1mc/7mc) |
08-252 |
reproducer for submarine announcing equipment |
08-253-254 |
submarine announcing equipment |
08-255-257 |
overall schematic for submarine announcing system circuit 1mc/7mc |
08-258 |
spare parts submarine announcing equipment |
08-259 |
submarine announcing equipment bridge reproducer |
08-260 |
submarine announcing equipment schematic diagram for power amplifier |
08-261 |
submarine announcing equipment reproducer |
08-262-263 |
submarine announcing equipment transmitter control station |
08-264 |
submarine announcing equipment mounting hook |
08-265 |
submarine announcing equipment pressure proof switch box |
08-266-267 |
submarine announcing equipment power amplifier |
08-268 |
submarine announcing equipment reproducer talk back switch |
08-269 |
submarine announcing equipment pressure proof switch box |
08-270-271 |
submarine announcing equipment power amplifier |
08-272 |
submarine announcing equipment reproducer talk back switch |
08-273-274 |
amplifier for submarine announcing equipment |
08-275-276 |
portable transmitter for battle announcing equipment |
08-277 |
shaft revolution indicator system circuit k list of spare parts and tools |
08-278 |
shaft revolution indicator system circuit k wiring diagram |
08-279-280 |
shaft revolution indicator system circuit k master indicator mi-6 type b |
08-281-282 |
shaft revolution indicator system circuit k shaft transmitter type t-3 watertight |
08-283 |
motor for trimming pump |
08-284-285 |
bulkheads non-structural for storeroom and engineers log room in maneuvering room |
08-286-287 |
after torpedo room joiner bulkheads |
08-288-290 |
platform deck forward and after engine rooms |
08-291-292 |
flats in pump room |
08-293 |
shell housing for signal ejector |
08-294-295 |
sound isolation hydraulic power plant in pump room |
08-296 |
sound isolation foundation for trim pump and motor |
08-297-298 |
foundations in control room for steering stand and navigation instruments |
08-299-300 |
foundations for navigation sound and torpedo control instruments in conning tower |
08-301-302 |
foundations for miscellaneous flasks |
08-303-304 |
foundations for additional oxygen flasks |
08-305-306 |
foundations for auxiliary power units, telephone, radar, interior communication equipment and periscope hoist controllers |
08-307-308 |
foundations for controllers for torpedo room |
08-309-311 |
foundations for controllers in engine rooms |
08-312-313 |
foundations for misc. electrical equipment in motor and maneuvering rooms |
08-314 |
sound isolation aux gyro compass control panel motor generator and master gyro compass |
08-315-316 |
foundations for misc. controllers gyro setting indicator resistors and torpedo firing panel in after torpedo room |
08-317-318 |
foundations for sj radar equipment in conning tower |
08-319 |
towing hook |
08-320-321 |
rails and stanchions main deck |
08-322 |
resistor for hydraulic power plant motor |
08-323-325 |
hydraulic system main power plant arrangement and piping |
08-326-328 |
hydraulic system power plant arrangement in pump room |
08-329-330 |
hydraulic system flanges and special fittings detail sheet #4 |
08-331-332 |
hydraulic system non-return valve 1200# test arrangement body and valve details |
08-333-334 |
hydraulic system flanges and special fittings detail sheet #3 |
08-335-336 |
hydraulic system flanges and special fittings sheet no 1 |
08-337 |
hydraulic system flanges and special fittings sheet no 2 |
08-338-339 |
hydraulic system bed plate for power plant arrangement and details |
08-340-341 |
steer gear hydraulic system instruction plates and name plates |
08-342 |
hydraulic system dc motor assembly |
08-343-344 |
dc magnetic controller for bow plane tilting stern plane tilting and after capstan |
08-345-346 |
dc magnetic controller for steering gear |
08-347-349 |
steering gear arrangement aft |
reel 9 |
09-001-003 |
steering gear general arrangement and diagram arrangement of piping |
09-004-006 |
steering gear arrangement of piping in after torpedo room |
09-007-009 |
steering gear control cylinder and pump control arrangement |
09-010-011 |
steering gear power plant bedplate |
09-012-013 |
steering gear flanges and special fittings details |
09-014-015 |
bow diving gear rigging gear hydraulic control valve body and miscellaneous details |
09-016-107 |
bow diving gear rigging gear hydraulic control valve misc. details |
09-018-019 |
bow diving gear rigging gear hydraulic control valve assembly |
09-020-021 |
bow diving gear contact makers for rigging and windlass arrangement and details |
09-022-023 |
bow diving gear tilting interlock valve arrangement and details |
09-024-025 |
bow and stern diving gear instruction plates |
09-026-027 |
hydraulic steering gear dc motor assembly |
09-028-029 |
steering gear rudder angle transmitter arrangement |
09-030-031 |
steering gear rudder angle transmitter foundation and shaft details |
09-032-033 |
steering gear rudder angle transmitter lever connecting rod and bracket details |
09-034 |
steering gear elementary wiring |
09-035-036 |
gyro compass system schematic and isometric wiring diagrams circuit lc |
09-037-038 |
conning tower arrangement |
09-039-040 |
control room arrangement |
09-041-042 |
chart room in control room |
09-043-044 |
periscope hoist motor control elementary wiring diagrams |
09-045-046 |
#1 periscope arrangement lower end |
09-047-048 |
periscopes arrangement lower end |
09-049-050 |
periscopes and vertical antenna mast supports greasing arrangement |
09-051 |
machinery builders plates |
09-052 |
label plates outside |
09-053-054 |
moment diagram |
09-055-056 |
misc. lockers and stowage in control room |
09-057-058 |
misc. lockers and stowage in pump room |
09-059-060 |
misc. lockers in forward engine room |
09-061-062 |
misc. lockers in after engine room |
09-063-064 |
misc. lockers in motor and maneuvering rooms |
09-065 |
officers duty board |
09-066-067 |
seats in wardroom and wr staterooms |
09-058-070 |
metal furniture officers and cpo quarters manufactured by building yard |
09-071-073 |
metal joiner work details galley and mess room |
09-074-075 |
plumbing system crews water closet aft piping arrangement |
09-076 |
fresh water system cooling coils arrangement and details |
09-077-078 |
ventilation system ships exhaust and engine air supply 22" hull valves including plate, gagging screw, foundations |
09-079-080 |
ventilation system engine air supply 15 1/2 hull valve valve disc lever slotted link and pins |
09-081-082 |
ventilation system engine air supply 15 1/2 hull valve hand lever dog and shafts |
09-083-084 |
ventilation system engine air supply 15 1/2 hull valve gag scr and foundations |
09-085-086 |
ventilation system engine air supply 15 1/2 hull valve cone |
09-087-088 |
ventilation system engine air supply 15 1/2 hull valve gear, gear box, shafts and supports |
09-089-090 |
ventilation system ships exhaust and engine air supply 22" hull valves hoods |
09-091-092 |
ventilation system 36" supply-exhaust and induction valve outboard valve seat and disc |
09-093-094 |
ventilation system diagram |
09-095-097 |
ventilation system general arrangement |
09-098 |
500 cfm battery ventilation fans |
09-099 |
heaters electric type b chromalux |
09-100 |
heaters electric type b chromalux |
09-101-102 |
arrangement of machinery after engine room |
09-103-104 |
starting air and pneumatic emergency stop diagram |
09-105 |
main engine exhaust system 15" inside valve (gate type) arrangement |
09-106-107 |
main engine exhaust system 15" disc, bearing and toggle arm |
09-108-109 |
main engine exhaust system outboard valves (drowned type 15") valve box and jacket |
09-110-111 |
main engine exhaust system outboard valves (drowned type 15") operating gear shaft block and gagging socket |
09-112-113 |
main engine exhaust system 15" inside valve gate type bonnet and valve disc details |
09-114-115 |
auxiliary engine exhaust system 15" inside exhaust valve (gate type) |
09-116-117 |
auxiliary engine exhaust system 15" inside exhaust valve (gate type) details and bonnet |
09-118 |
ships plan list |
09-119-120 |
main engine exhaust system outside valves (drowned type 15") assembly |
09-121-122 |
main engine exhaust system outside valves (drowned type 15") operating gears arrangement |
09-123-124 |
main engine exhaust system outside valves (drowned type 15") elbow development of inside surface |
09-125-126 |
main engine exhaust system outside valves (drowned type 15") shafts,pins, levers and bushings |
09-127-128 |
main engine exhaust system outside valves (drowned type 15") tank covers |
09-129-130 |
main engine exhaust system outside valves (drowned type 15") and inside valves operating gear foundations |
09-131-132 |
main engine exhaust system outside valves (drowned type 15") spray pipe for discharge |
09-133-134 |
main engine exhaust system outside valves (drowned type 15") spacer -counterweight and spray shield for seat |
09-135-136 |
main engine exhaust system 15" inside valves (gate type) valve body |
09-137-138 |
main engine exhaust system expansion joints and lagging |
09-139-141 |
main and aux. engine exhaust system valves mufflers and piping arrangement |
09-142-143 |
main engine exhaust system outside valves (drowned type 15") elbow |
09-144-145 |
main engine exhaust system inside exhaust pipe water jacketed |
09-146-147 |
main engine exhaust system inside exhaust pipe water jacketed |
09-148-149 |
starting air emergency stop piping arrangement forward and after engine rooms |
09-150 |
main engine exhaust system 15" inside valve (gate type) hand operated gear and detail and seat |
09-151-152 |
main engine exhaust system outside valves (drowned type 15") tank and reinforced disc |
09-153-154 |
main engine exhaust muffler |
09-155 |
speed load and tvg instruction plates |
09-156 |
main propulsion control arrangement of battery cable terminals |
09-157-158 |
main engine cylinder lifting gear arrangement and details |
09-159-160 |
arrangement of machinery forward engine room |
09-161-162 |
main engine gauge boards valve and piping arrangement engine rooms |
09-163-164 |
main shafting fairwaters at struts propeller bore shaft template |
09-165-166 |
connection of shaft tube casting to shell |
09-167-169 |
lubricating oil system piping arrangement motor room |
09-170-171 |
lube oil purifier and transfer system piping arrangement forward engine room |
09-172-173 |
plug cock (1 1/4" nominal) lube oil system forward engine room |
09-174-175 |
special fittings lube oil systems engine rooms |
09-176-177 |
manifold lube oil system absorbent filter bypass |
09-178-179 |
lube oil system piping arrangement forward engine room |
09-180-181 |
lube oil system piping arrangement aft engine room |
09-182-183 |
lube oil system piping diagram machinery spaces |
09-184 |
1 1/2" bypass relief valve auxiliary engine lube oil cooler after engine room |
09-185-186 |
special fittings lube oil system motor room |
09-188 |
3" relief valve (10-25#) lube oil system forward and after engine rooms |
09-189-190 |
lube oil purifier and trans. system piping arrangement after engine room |
09-191-192 |
control room drains |
09-193-194 |
100-gal trim and 35 gal drain pump horizontal drive morse morlex coupling installation |
09-195-196 |
centrifugal trim pump (gould) frahm vibrating reed tachometer installation and details |
09-197-198 |
trim pump lubricator piping arrangement |
09-199 |
foundations for centrifugal trim pump seal water tank and vacuum pump |
09-200-201 |
fresh water circulating system piping arrangement forward engine room |
09-202-203 |
special fittings fresh water circulating system engine room |
09-204-206 |
sea water circulating system piping arrangement after engine room |
09-207-208 |
fresh water circulating system piping arrangement aft engine room |
09-209-210 |
sea water circulating system piping arrangement forward engine room |
09-211 |
circulating sea water system 2" manifold after engine room |
09-212 |
5" nominal macomb strainer main generator engines |
09-213 |
2 1/2" nominal macomb strainer after engine rooms |
09-214-215 |
sea water circulating system 2" quick opening valve engine room |
09-216-217 |
fresh water system engine rooms, sylphon valve tubing guard arrangement and details |
09-218-219 |
fresh water circulating system horizontal swing check valve 4 1/4" nominal after engine room |
09-220-221 |
circulating sea water system horizontal swing check valve 4 1/4" nominal after engine room |
09-222-223 |
fresh water circulating system horizontal swing check valve 3" nominal forward and after engine rooms |
09-224 |
main engine oil pan drain to sump tank stuffing box |
09-225-226 |
main and aux. engine exhaust system circulating water fittings sheet no 1 |
09-227-228 |
main and aux. engine exhaust system circulating water fittings sheet no 2 |
09-229-230 |
main and aux. engine exhaust system muffler vent and circulating water fittings |
09-231-233 |
circulating water piping arrangement air conditioning refrigerating and hp air compressors pump room |
09-234-235 |
special fittings sea water circulating system engine rooms |
09-236-237 |
plumbing system sea connections details |
09-238-239 |
whistle pull and air piping arrangement |
09-240-241 |
whistle pull details |
09-242-243 |
engines emergency stop control valve main and auxiliary engines arrangement and details |
09-244-245 |
main storage battery tanks forward and aft stowage of ships air flasks |
09-246-248 |
salvage system general arrangement |
09-249 |
special fittings fuel oil system forward and aft engine rooms |
09-250-251 |
fuel oil system piping diagram engine rooms |
09-252-253 |
fuel oil system piping arrangement forward engine room |
09-254-255 |
fuel oil system piping arrangement after engine room |
09-256 |
piping diagram distilling system forward engine room |
09-257 |
distiller gauge boards |
09-258 |
ships plan index 750 gpd vapor compression distilling units |
09-259-260 |
distilling system de-superheating tank and special fittings forward engine room |
09-261-263 |
distilling system piping arrangement forward engine room |
09-264 |
circulating water piping air conditioning and refrigeration diagram |
09-265-266 |
air conditioning and refrigeration elememntary and isometric diagram |
09-267-270 |
air conditioning and refrigeration refrigeration piping arrangement pump room |
09-271-273 |
air conditioning and refrigeration refrigeration piping arrangement outside of pump room |
09-274 |
motor for refrigeration circulating water pump |
09-275 |
motor for air conditioning circulating water pump |
09-276 |
refrigeration plant ice cube maker cabinet |
09-277-278 |
dc magnetic controller for refrigeration compressor and circulating water pump |
09-279 |
motor for refrigerating compressors |
09-280 |
refrigeration system diagrammatic arrangement of freon piping for refrigerator in officers pantry |
09-281-282 |
auxiliary generator and after distribution switchboard details 1 |
09-283-284 |
auxiliary generator and after distribution switchboard details 2 |
09-285-286 |
ac supply and internal communications distribution diagram |
09-287-288 |
ic switchboard preliminary wiring diagram |
09-289-290 |
lighting system switchboard details |
09-291-292 |
aux. power distribution panel 2-35-1 forward engine room assembly and details |
09-293-294 |
aux. power distribution panel 2-35-1 forward engine room box and cover |
09-295-296 |
aux. power distribution panel 2-78-1 forward engine room details |
09-297-298 |
aux. power distribution panel 2-100-2 maneuvering room assembly and details |
09-299 |
aux. power distribution panel 2-100-1 maneuvering room box and cover |
09-300-301 |
aux. power distribution panel 2-98-1 after engine room assembly and details |
09-302 |
aux. power distribution panel 2-98-1 after engine room box and cover |
09-303-304 |
aux. power distribution panel 2-65-1 crew's mess assembly and details |
09-305-307 |
aux. generator and after distribution switchboard assembly |
09-308 |
auxiliary power distribution diagram |
09-309-310 |
main power system wiring deck plan |
09-311-312 |
main power system feeder list |
09-313-314 |
auxiliary power distribution panel 2-55-2 radio room panel assembly and details |
09-315-316 |
forward distribution switchboard and compartment distribution switchboard control room assembly |
09-317-318 |
forward distribution switchboard and compartment distribution switchboard control room details no 1 |
09-319-320 |
forward distribution switchboard compartment distribution switchboard control room details no 2 |
09-321-322 |
ac aux power generator and distribution switchboard assembly |
09-323-324 |
ac aux power generator and distribution switchboard details |
09-325-326 |
auxiliary power distribution panel 2-78-1 forward engine room assembly and details |
09-327-328 |
main and aux. power system forward battery terminal connections details |
09-329-230 |
main and aux. power system after battery terminal connections details |
09-331-332 |
main and aux. power system arrangement of forward battery terminals and disconnect switches |
09-333-334 |
main and aux. power system arrangement of after battery terminals and disconnect switches |
09-335-336 |
aux power system forward and after battery compartment auxiliary power and lighting switch |
09-337-338 |
aux. power system wiring deck plan-forward |
09-339-341 |
aux. power system list of material feeders and mains |
09-342-343 |
aux. power system wiring deck plan aft |
09-344-345 |
individual cell switch panel voltmeters assembly and details |
09-346-347 |
main power system generator no 1 and no 2 connections |
09-348 |
list of switches and meters on switchboards (illegible) |
09-349-350 |
wireways and supports aft |
09-351-352 |
ac feeders wiring deck plan |
09-353-354 |
aux power system shore connection terminal box |
09-355-356 |
misc. parts for electrical installations |
reel 10 |
10-001 |
repair parts de leval imo pump |
10-002 |
main motor control list of spare parts |
10-003 |
summary list of spare parts?? |
10-004 |
diesel engines summary list of spare parts |
10-005 |
diesel engines summary list of spare parts |
10-006 |
diesel engines summary list of spare parts |
10-007 |
main generator main motors aux generators spare parts and tools elliot company |
10-008 |
motor for vertical antenna, #1 periscope and #2 periscope |
10-009 |
motor for battery ventilation blower |
10-010 |
motor for hull ventilation supply fan |
10-011 |
motor for hull hull ventilation exhaust fan |
10-012-13 |
summary list of spare parts diesel engine |
10-014-015 |
summary list of spare parts diesel engine |
10-016-017 |
summary list of spare parts diesel engine |
10-018 |
motor for drainage pump |
10-019 |
illegible |
10-020 |
motor for high pressure air compressor |
10-021 |
motor for air conditioning circ. water pump |
10-022-023 |
consolidated spare parts for auxiliary motors |
reel 11 |
11-001-002 |
sound isolation flexible pipe connection |
11-003-004 |
stern torpedo tubes and steering gear greasing arrangement |
11-005-006 |
stern torpedo tubes and steering gear greasing details |
11-007-008 |
foundations in forward torpedo room for echo ranging listening equipment |
11-009-011 |
4"/50 cal. pressure proof ready service locker |
11-012-013 |
foundations for 4"/50 cal. pressure proof ready service locker |
11-014-015 |
ventilation system ships exhaust and engine air supply 22" hull valve at fr 76 valve seat |
11-016-017 |
ventilation system engine air supply at frame 92 1/2 22" hull valve valve seat |
11-018-019 |
ventilation system engine air supply 15 1/2" hull valve valve disc lever slotted link and pins |
11-020-021 |
ventilation system engine air supply 15 1/2" hull valve, valve cover |
11-022 |
300 kw auxiliary generator uniform specifications and spare parts and tools |
11-023 |
plan list main storage battery |
11-024 |
foundation for sparling flow meter |
11-025-027 |
fresh water and plumbing piping arrangement officer's quarters and forward battery compartment |
11-028 |
sound isolation gyro setting indicator regulator |
11-029-030 |
5" gun muzzle support |
11-031-032 |
foundation for 5" gun aft |
11-033-034 |
forward torpedo loading hatch swing bolt torpedo hatch arrangement and details |
11-035-036 |
aft torpedo loading hatch swing bolt torpedo hatch arrangement and details |
11-037-040 |
5"/25 cal. pressure proof ready service locker |
11-041-043 |
ammunition and ordnance stowage |
11-044-045 |
platform deck in conning tower |
11-046 |
foundations for reproducers |
11-047-049 |
foundations for navigation sound and torpedo control instruments in conning tower |
11-050-051 |
foundation for sj-1 radar over head training mechanism in conning tower |
11-052-053 |
foundation for radar equipment in conning tower |
11-054 |
foundation for true bearing indicator in control room |
11-055-056 |
foundations for target bearing transmitter on bridge |
11-057-058 |
operating seat for jp-1 sound equipment in forward torpedo room |
11-059-060 |
hatch cover 25" diameter dished plate for conning tower and gun access handwheel interlock arrangement and details |
11-061-062 |
chart table and foundation for mark vii dead reckoning tracer in conning tower |
11-063-064 |
air system installation of muffler for negative tank vent line to bilge |
11-065-066 |
model st radar periscope type arrangement of equipment in control room |
11-067-068 |
model sj-1 radar equipment training mechanism overhead power drive general arrangement |
11-069-070 |
echo ranging and detection lower drift stop quill bearing type arrangement and details |
11-071 |
air conditioning plant, type prini4 pressure regulation valve |
11-072-073 |
3" diameter voice tube system bridge to conning tower arrangement and details |
11-074-076 |
radio and sound systems wiring deck plans |
11-077-079 |
model wca-2 echo ranging listening and model jp-1 sound receiving equipment arrangement in forward torpedo room |
11-080-081 |
test built in tanks and compartments |
11-082-083 |
shore connection box lighting assembly and details |
11-084-085 |
foundation for trim pump deep well |
11-086-087 |
compartments and tanks |
11-088-090 |
water and drainage piping arrangement pump room for deep well pump |
11-091-092 |
fuel oil tanks try cock system piping arrangement |
11-093-094 |
stowage of fuel oil filling hose |
11-095-096 |
bulkheads non-structural officers and cpo quarters |
11-097-098 |
foundation for diving gear control and indicating mechanism in control room |
11-099-101 |
platform deck covering |
11-102-104 |
compartment and access |
11-105-106 |
bow and stern diving gear hydraulic pump and emergency control valve bedplate details |
11-107-109 |
miscellaneous details in officers and cpo quarters |
11-110-112 |
metal furniture officers and cpo quarters manufactured by building yards |
11-113-114 |
ventilation system officers quarters and forward battery arrangement |
11-115-116 |
ventilation system forward torpedo room arrangement |
11-117-121 |
piping outside tanks forward |
11-122-124 |
fuel oil water and drainage piping arrangement after battery room |
11-125-128 |
piping in outside tanks aft |
11-129-131 |
fuel oil water and drainage piping arrangement crew's mess and galley and scullery |
11-132-133 |
trimming system trim pump change valve remote control arrangement and detail |
11-134-136 |
fresh water and plumbing piping arrangement crew's quarters and aft battery compartment |
11-137-139 |
air piping arrangement crews quarters and after battery space |
11-140-142 |
air system piping arrangement crews mess galley and scullery |
11-143-144 |
fuel oil system diagram |
11-145-146 |
main and aux. power system arrangement of forward and after battery terminals and disconnect switches |
11-147-148 |
main and aux. power system forward and after battery terminal connections details |
11-149-150 |
aux. power and lighting switch forward and after battery compartment |
11-151 |
disconnect switch for emergency lighting system assembly and installation |
11-152-153 |
main battery disconnect switch operating gear arrangement |
11-154-155 |
main battery disconnect switch operating gear details |
11-156-157 |
model wca-2 echo sounding equipment circuit s-es arrangement in ship and diagram and external wiring diagram |
11-158-159 |
model wca-2 echo sounding equipment circuit s-er arrangement in ship and diagram and external wiring diagram |
11-160-161 |
model wca-2 echo sounding equipment circuit s-rc diagrammatic and external wiring diagram |
11-162-163 |
foundation for general motor aux. generating set |
11-164 |
foundations for misc. equipment for aux. main generating set |
11-165-167 |
arrangement of machinery in after engine room |
11-168-171 |
main and aux. engine exhaust system valves mufflers and piping arrangement |
11-172-173 |
main engine exhaust system outboard valve (drowned type 15") elbow |
11-174-176 |
lube oil system piping arrangement after engine room |
11-177-179 |
lube oil purifier and transfer system piping arrangement after engine room |
11-180-182 |
fresh water circulating system piping arrangement aft engine room |
11-183-185 |
sea water circulating system piping arrangement after engine room |
11-186-187 |
circulating sea water system 3" manifold after engine room |
11-188-189 |
fresh water circulating system special fittings engine rooms |
11-190-191 |
main and aux. engine exhaust system circulating water fittings. |
11-192-193 |
sea water circulating system special fittings engine room |
11-194-196 |
starting air emergency stop piping arrangement forward and after engine rooms |
11-197-198 |
special fittings fuel oil system forward and aft engine rooms |
11-199-201 |
fuel oil system piping arrangement after engine room |
11-202 |
list of ships plans auxiliary engine |
11-203-204 |
auxiliary engine exhaust system 8" inside exhaust valve gate type arrangement |
11-205-206 |
auxiliary engine exhaust system 8" inside exhaust valve gate type valve body and seat |
11-207-208 |
auxiliary engine exhaust system 8" inside exhaust pipe water jacketed |
11-209-210 |
auxiliary engine exhaust system inside elbow water jacketed |
11-211-212 |
?? pump air domes, ?? |
11-213-214 |
pyrometer system elementary and isometric |
11-215-216 |
aux. engine gauge board valves and piping arrangement after engine room |
11-217-218 |
thermometer and gauge list |
11-219-220 |
foundation for 4" and 5" gun forward |
11-221-222 |
main storage battery tanks forward and aft stowage of ships air flasks |
11-223-224 |
shore connection switch for lighting switchboard |
11-225-227 |
interior communication battle telephone and call bell system elementary and isometric wiring circuit e |
11-228-229 |
demolition outfit stowage |
11-230-231 |
4" gun muzzle support |
11-232-233 |
four inch gun firing clearances |
11-234-236 |
platform deck officers quarters |
11-237-239 |
platform deck crews quarters galley and crews mess |
11-240-241 |
#1 periscope arrangement lower end |
11-242-243 |
periscopes arrangement lower end |
11-244-245 |
no 1 and no 2 periscopes fixed grease gun arrangement and details |
11-246-247 |
sliding berths details |
11-248-250 |
water and drainage piping arrangement pump room |
11-251-254 |
meat and cool rooms arrangement and details |
11-255 |
sound isolation foundations for fan motors hull ventilation system |
11-256 |
method of sealing solderless pressed on terminal lugs onto shfl-800 and shfl-650 |
11-257-258 |
ammunition hoist |
11-259-260 |
wrench stowage topside |
11-261-262 |
ac feeders wiring deck plan |
11-263-264 |
ac supply and internal communications distribution diagram |
11-265-266 |
shaft revolution transmitter sheaves and drive |
11-267-268 |
mark iii iff equipment arrangement in ship |
11-269 |
foundations for magnetic compasses in conning tower and control room |
11-270-271 |
log desk in engine rooms |
11-272 |
ships plan list |
11-273 |
summary list of spare parts for main engine diesels |
11-274 |
summary list of spare parts for main engine |
11-275 |
summary list of spare parts for main engine |
11-276 |
summary list of spare parts for main engine |
11-277 |
summary list of spare parts for main engine |
11-278-279 |
sea water circulating system 4" macomb strainer motor room |
11-280-281 |
sea water circulating system 5" macomb strainer forward and aft engine room |
11-282 |
list of ships spare parts, auxiliary engine |
11-283 |
master drawing index, main generators, main motors, aux. generators |
11-284 |
spare parts and tools main generators, main motors, aux. generators |
11-285 |
foundations for reproducers |
11-286-287 |
radio antenna system arrangement and details |
11-288-289 |
torpedo charging heating and hydrogen burning equipment and wiring basic mark 18 torpedo |
11-290-292 |
superstructure side and main deck frames 10 to 45 incl. |
11-293-295 |
superstructure frames 32 to 43 incl. |
11-296-297 |
after torpedo room joiner bulkheads |
11-298-299 |
bulkheads non-structural officers and cpos quarters |
11-300-301 |
bulkheads non-structural crews w.c. washroom and shower |
11-302-304 |
bulkheads non-structural galley and mess room |
11-305 |
bulkheads non-structural officers wc and shower forward torpedo room |
11-306 |
foundations for sound system motor starter qc, jk and qb |
11-307-308 |
main deck wood |
11-309-311 |
metal joiner doors |
11-312-313 |
metal joiner door list |
11-314-316 |
conning tower fairwater and bridge joiner work seats and platforms |
11-317-318 |
drying locker for binoculars |
11-319-321 |
chart table and plotting paper role mechanism in conning tower |
11-322-323 |
storerooms below platform deck |
11-324-325 |
extension table wardroom |
11-326-328 |
metal furniture officers and cpo quarters manufactured by building yard |
11-329-331 |
miscellaneous details in officers and cpo quarters |
11-332-333 |
misc. metal joiner details |
11-334-335 |
lockers in after torpedo room arrangement and detail |
reel 12 |
12-001-002 |
after torpedo tube shutters and tracks details |
12-003-004 |
after torpedo tube shutters arrangement and line |
12-005-006 |
submerged log housing tube and foundations arrangement and details |
12-007-008 |
platform deck in conning tower |
12-009-010 |
gun access trunk and 20 mm gun foundation |
12-011 |
method of plugging holes |
12-012-013 |
ventilation system forward torpedo room arrangement |
12-014-015 |
ventilation system after torpedo room arrangement |
12-016-017 |
trimming system trim pump manifold |
12-018 |
manifold 200# air service sheet #1 |
12-019 |
manifold 200# air service sheet #2 |
12-020-021 |
fresh water tanks capacity test manifold piping arrangement |
12-022-023 |
inboard vent valve negative tank |
12-024 |
fuel oil system four valve manifold |
12-025 |
arrangement of contact maker negative tank vent valve control room |
12-026 |
fuel oil compensating system manifolds |
12-027 |
trimming system sea connection |
12-028-029 |
fresh water and plumbing piping arrangement maneuvering room |
12-030-031 |
air flow meter piping arrangement |
12-032 |
refrigeration plant and hp air compressor sea connection |
12-033-034 |
water and drainage piping arrangement forward torpedo room |
12-035 |
fuel oil fill and compensating lines, incomplete drawing |
12-036 |
foundations for wca-2 sound system motor generators |
12-037-038 |
model wca-2 echo ranging listening sounding equipment cir s-rc diagrammatic and external wiring diagrams |
12-039-040 |
model wca-2 echo ranging listening sounding equipment cir s-er diagrammatic and external wiring diagrams |
12-041-042 |
storage battery ventilation air supply ducts |
12-043-044 |
medical locker |
12-045-046 |
mess gear stowage in mess benches |
12-047-048 |
galley metal joiner work |
12-049-050 |
lockers in forward torpedo room arrangement and details |
12-051-053 |
model wca-2 echo ranging and listening equipment and model sj-1 radar equipment arrangement in conning tower |
12-054-055 |
model wca-2 sonar equipment cable entrances in rear of units assembly and details |
12-056-057 |
torpedo tube shutters forward upper arrangement and lines |
12-058-059 |
torpedo tube shutters forward middle arrangement and lines |
12-060-061 |
torpedo tube shutters forward lower arrangement and lines |
12-062-063 |
forward torpedo tube shutters details of upper shutters |
12-064-065 |
torpedo tube shutters middle and lower details |
12-066-067 |
four inch gun clearances |
12-068-069 |
foundations for no 1 and 2 periscope and vertical antenna mast motor hoists |
12-070-071 |
foundations for controllers in forward torpedo room |
12-072 |
no 1 and 2 periscopes stuffing box packing installation |
12-073-074 |
ventilation system ships supply 15 1/2 hull valve valve seat |
12-075 |
ships plan list for auxiliary engine |
12-076 |
10# blow system low pressure blower lube oil pump press gauge piping arrangement |
12-077 |
summary list of spare parts for auxiliary generator set |
12-078 |
summary list of spare parts for auxiliary generator set |
12-079 |
summary list of spare parts for auxiliary generator set |
12-080 |
summary list of spare parts for auxiliary generator set |
12-081-082 |
superstructure frames 68 to 79 inclusive |
12-083-084 |
foundation for 5"/25 cal pressure proof ready service locker aft |
12-085-086 |
rails and stanchions main deck |
12-087-089 |
main deck wood |
12-090-091 |
forward escape trunk structure |
12-092-093 |
stowage for manila rope and deck gear in superstructure |
12-094-095 |
radio room drawers for vacuum tube stowage assembly and details |
12-096-097 |
5" ammunition passing scuttle arrangement |
12-098-099 |
5" ammunition passing scuttle breech base details |
12-100-101 |
5" ammunition passing scuttle cover and link details |
12-102-103 |
5" ammunition passing scuttle locking ring and bearing details |
12-104-105 |
5" ammunition passing scuttle tube and stuffing box details |
12-106-107 |
5" ammunition passing scuttle shafting and indicator details |
12-108-109 |
5" ammunition passing scuttle breech and muzzle door operating details |
12-110-111 |
after five inch gun firing clearances |
12-112-113 |
access hatches flush type welded 20x20, 15x23 |
12-114 |
low pressure blow system fittings for use with discharge snubber |
12-115-117 |
lighting system wiring deck plan |
12-118-120 |
lighting system list of feeders wiring appliances and fixtures block and elementary wiring diagrams |
12-121-122 |
location of fans, reproducers, talkback switches and horns |
12-123-124 |
echo ranging and detection equipment hydraulic piping arrangement |
12-125-126 |
frames 48-49-50 |
12-127-128 |
frames 51-52-53 |
12-129-130 |
compartments and access |
12-131-134 |
superstructure sides and main deck frames 66 to 125 incl. |
12-135 |
main shafting rubber covering stern tube shaft details |
12-136-137 |
propeller shaft and coupling details |
12-138-139 |
bulkhead 107 |
12-140-141 |
pressure proof terminal box (spark plug type) for searchlight |
12-142-143 |
target designation system circuit gt isometric wiring diagram |
12-144-146 |
target designation system circuit gt elementary wiring diagram |
12-147-148 |
foundations for navigation sound and torpedo control instruments in conning tower |
12-149 |
foundations for st radar equipment in control room |
12-150-151 |
steering gear connecting rod stuffing box bearing sliding sleeve |
12-152-153 |
chart table in conning tower |
12-154 |
#1 and #2 periscopes azimuth circle |
12-155-156 |
flood valves seat cover details safety tank |
12-157-158 |
flood valves seat and cover details negative tank |
12-159-160 |
air conditioning refrigeration piping arrangement in conning tower |
12-161-163 |
model wca-2 echo ranging and listening equipment and model sj-1 radar equipment arrangement in conning tower |
12-164-166 |
supports for no 1 and 2 periscopes vertical antenna mast and radar |
12-167-168 |
foundations for supports for periscopes, vertical antenna mast and radar |
12-169-170 |
hydraulic system pilot valve for auto bypass and accumulator control motor limit switch arrangement |
12-171-172 |
hydraulic system pilot valve body piston and details |
12-173-174 |
illegible ?? |
12-175-177 |
periscopes hydraulic general arrangement |
12-178-179 |
periscopes hydraulic arrangement lower end |
12-180-181 |
periscopes hydraulic cylinder and piston arrangement and details |
12-182-183 |
periscopes hydraulic hull casting and stuffing box details |
12-184-185 |
periscopes hydraulic lifting ring details |
12-186-187 |
illegible ?? |
12-188-189 |
periscopes hydraulic light shield details |
12-190-191 |
periscopes hydraulic control body and piston arrangement and details |
12-192-193 |
periscopes hydraulic control valve lever and misc. details |
12-194-195 |
periscopes hydraulic bumper arrangement and details |
12-196-197 |
periscopes hydraulic piping arrangement |
12-198-201 |
molded offsets out hull and superstructure afterbody |
12-202-204 |
inner shell expansion |
12-205-208 |
top of hull and bottom of conning tower holes and attachments |
12-209-211 |
superstructure frames 92 to 109 inclusive |
12-212 |
after torpedo room tank top |
12-213-214 |
frames 98-99-100 |
12-215-216 |
frames 101-102-103 |
12-217-218 |
frames 104-105-106 |
12-219-220 |
frames 108-109-110-111 |
12-221-222 |
frames 112-113-114-115 |
12-223-224 |
frames 116-117-118-119 |
12-225-226 |
bulkhead 13 1/2 forward frame 99 |
12-227-228 |
bulkhead 107 |
12-229-231 |
holes and attachments bulkhead 13 1/2 forward frame 99 |
12-232-233 |
holes and attachments bulkhead frame 107 |
12-234-235 |
holes and attachments bulkhead frame 88 |
12-236-237 |
platform deck maneuvering room |
12-238-239 |
flats in motor room |
12-240-241 |
foundation for oxygen flasks |
12-242 |
lathe foundation maneuvering room |
12-243-244 |
foundation for main motor salt water and lube oil accessories |
12-245-247 |
foundations for misc. electrical equipment in motor and maneuvering rooms sheet 1 |
12-248-249 |
foundations for gauge boards in forward and after torpedo rooms |
12-250-251 |
foundations for misc. electrical equipment in maneuvering room |
12-252-253 |
foundations for mod. sj radar equipment in conning tower |
12-254 |
maneuvering room deck covering |
12-255-256 |
compartments and tanks |
12-257-259 |
compartment and access |
12-260-262 |
portable plates in forward and after engine rooms and maneuvering room |
12-263 |
manhole list boiler type flat plate dished plate and flush type |
12-264-265 |
metal joiner door list |
12-266-269 |
ladders and grabs |
12-270 |
after capstan portable push button assembly and details |
12-271-272 |
hydraulic system piping arrangement maneuvering room |
12-273 |
foundation for sea water circulating pump |
12-274 |
foundation for ac motor generator sets |
12-275-276 |
foundations for lube oil standby and main motor bearing pumps in motor room |
12-277 |
label plates outside |
12-278 |
label plates inside |
12-279-280 |
curves of capacity, center of gravity and moment of inertia lube oil tanks |
12-281-282 |
test built in tanks and compartments |
12-283 |
engineers log room |
12-284-285 |
miscellaneous lockers in motor and maneuvering rooms |
12-286-287 |
work bench and log desks in maneuvering room |
12-288-289 |
ventilation system 11" bulkhead valves, bulkhead 13 1/2 forward frame 99 arrangement |
12-290-291 |
ventilation system engine air supply 15 1/2 hull valve, valve seat |
12-292-294 |
ventilation system engine air supply 15 1/2 hull valve, assembly |
12-295-296 |
ventilation system engine air supply 15 1/2 hull valve, maneuvering room arrangement |
12-297-298 |
ventilation system engine air supply 15 1/2 hull valve air duct |
12-299-300 |
ventilation system engine air supply 15 1/2 hull valve foundation |
12-301-302 |
ventilation system engine air supply 15 1/2 hull valve hand lever, dog, pawl,arms,shafts and gagging system |
12-303-306 |
ventilation system general arrangement |
12-307-308 |
ventilation system after engine room arrangement |
12-309-310 |
ventilation system maneuvering and motor rooms arrangement |
12-311-313 |
air induction and ventilation piping outboard |
12-314-315 |
machinery arrangement motor room |
12-316 |
propulsion motor and generators spare parts and tools |
12-317 |
ships plan list motor and generators |
12-318-319 |
main propulsion control motor and generator cable arrangement in motor room |
12-320-321 |
main propulsion control motor and generator connections details |
12-322-324 |
arrangement of machinery after engine room |
12-325-326 |
main propulsion control flexible connectors for 800,000 cm cable terminals |
12-327-328 |
main propulsion control control arrangement of battery cable terminal |
12-329-330 |
foundation for main propulsion control |
12-331-332 |
propulsion control group enclosure |
12-333-335 |
foundations for main motors |
12-336-337 |
main motor and propeller shaft turning and locking gear arrangement |
12-338-339 |
main motor and propeller shaft turning and locking gear housing, cage bearing and block |
12-340-341 |
main motor and propeller shaft turning and locking gear worm gear and foundation |
12-342-344 |
main shafting arrangement |
12-345 |
main shafting fairwaters at stern tubes |
12-346-347 |
main shafting coupling and turning gear guard |
12-348-349 |
main shafting bearings stern tube strut and stuffing box |
12-350-352 |
shaft tubes |
12-353-355 |
lubricating oil system piping diagram machinery spaces |
12-356-358 |
lubricating oil system piping diagram arrangement motor room |
12-359-360 |
lube oil system special fittings motor room |
12-361-362 |
lube oil system special fittings engine room |
12-363-364 |
lube oil system 1 1/2" by pass relief valve motor room |
12-365-366 |
lube oil system 1" by pass relief valve motor room |
12-367-370 |
lube oil system piping arrangement after engine room |
12-371 |
sounding rods for lubricating oil tanks and clean fuel oil tanks |
12-372-375 |
air-oil-water and vent systems piping in superstructure forward of frame no 70 |
12-376-379 |
air-oil-water and vent systems piping in superstructure aft of frame no 69 |
12-380-383 |
piping in outside tanks forward |
12-384-388 |
piping in outside tanks aft |
12-389-390 |
fuel oil water and drainage piping arrangement motor and maneuvering rooms |
12-391 |
sumps secondary drainage system |
12-392-394 |
circulating sea water system machinery compartment diagram |
12-395 |
circulation water details motor room |
12-396-398 |
sea water circulating system piping arrangement motor room |
12-399-400 |
sea water system manifold 1 1/4" nominal motor room |
12-401-402 |
salt water system 4" macomb strainer motor room |
12-403-404 |
sea water system three way cock 12 1/2" nominal size motor room |
12-405-406 |
circulating sea water system special sea valve 3/4" nominal size motor room |
12-407-408 |
sea water circulating system main engine overboard discharge sea valve 5" nominal size |
12-409-410 |
sea water circulating system 8" sea suction valve forward and after engine rooms |
12-411-412 |
sea connections seawater circulating systems main and aux. engines and motors |
12-413-414 |
hull and deck fittings salvage air fuel and lubricating oil systems |
12-415-417 |
air piping arrangement maneuvering and motor rooms |
12-418-419 |
air system piping arrangement in conning tower |
12-420-422 |
salvage system general arrangement |
12-423-424 |
fuel oil tanks try cock system piping arrangement |
12-425-428 |
air conditioning and refrigeration, refrigerant piping arrangement in pump room |
12-429-432 |
air conditioning and refrigeration, refrigerant piping arrangement outside of pump room |
12-433-434 |
refrigeration system air conditioning and refrigeration diagram |
12-435 |
submarine propulsion control master drawing list |
12-436 |
submarine propulsion control list of spare parts |
12-437-438 |
ac aux. power generator and distribution switchboard assembly |
12-439-440 |
ac aux. power generator and distribution switchboard details |
12-441-443 |
main power system wiring deck plan |
12-444-445 |
main power system feeder list |
12-446-447 |
main power system generator connections |
12-448-449 |
wireways and supports aft |
12-450-451 |
auxiliary power system wiring deck plan aft |
12-452 |
stowage of cell jumpers in battery tanks |
12-453-454 |
ic system engine control indicator system elementary and isometric wiring diagrams circuit 3mb |
12-455-456 |
engine control indicator system transmitter for maneuvering room assembly details circ 3mb |
12-457-458 |
marker buoy forward and aft installation in superstructure and releasing mechanism sheet 1 |
12-459-460 |
marker buoy forward and aft installation in superstructure and releasing mechanism sheet 2 |
12-461-463 |
shaft revolution transmitter arrangement and details |
12-464-465 |
illegible ?? |
12-466-467 |
model sj-1 radar equipment training mechanism arrangement of lower end |
12-468-469 |
model wca-2 echo ranging and listening equipment and model sj-1 radar equipment arrangement in conning tower |
12-470-471 |
torpedo handling and stowage after deck skid |
12-472-473 |
gauge and thermometer list |
12-474-475 |
gauge boards arrangement and details maneuvering room |
12-476 |
holophane light supports |
12-477-478 |
shaft revolution transmitters arrangement and details |
12-479-480 |
ventilation condensation tanks and foundations |
12-481-482 |
periscope hydraulic lifting yoke details |
12-483-484 |
illegible ?? |
12-485-486 |
signal ejector arrangement in ship hydraulic type, air operated |
12-487-489 |
signal ejector arrangement hydraulic type air operated |
12-490-491 |
signal ejector barrel details hydraulic type air operated |
12-492-493 |
signal ejector muzzle door operating details hydraulic type air operated |
12-494-495 |
signal ejector breech mechanism details hydraulic type air operated |
12-496-497 |
illegible ?? |
12-498-499 |
signal ejector breech mechanism hydraulic type air operated |
12-500-501 |
illegible ?? |
12-502-503 |
propeller shaft and coupling |
12-504-505 |
air system piping arrangement in conning tower |
12-506-508 |
radio and sound systems wiring deck plans |
12-509-511 |
model wca-2 echo ranging and listening equipment circ. s-es arrangement in ship diagram and external wiring diagram |